Answered: q= 26.36 kPa H = 2 m Y19 kN/m2 O= 25 H2…

Engineering

Civil Engineering

q= 26.36 kPa H = 2 m Y19 kN/m2 O= 25 H2 =4 m Y = 20 kN/m O= 30 Base

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume a Space Launch System (Figure 1(a)) that is approximated as a cantilever undamped single degree of freedom (SDOF) system with a mass at its free end (Figure 1(b)). The cantilever is assumed to be massless. Assume a wind load that is approximated with a concentrated harmonic forcing function p(t) = p.sin (wt) acting on the mass. The known properties of the SDOF and the applied forcing function are given below. • Mass of SDOF: m = 120 kip/g • Acceleration of gravity: g = 386 in/sec² Bending sectional stiffness of SDOF: EI= Height of SDOF: h= 3000 inches • Amplitude of forcing function: p. = 6 kip Forcing frequency: f = 8 Hz O RESIS POLIS O (a) Space Launch System on launching pad p(t)-> 1015 lbfxin² 111 u(t) El, h (b) Equivalent single degree. of freedom system without linear viscous damper Rigid Support p(t)→ 111 u(t) EI, h C Rigid Support (c) Equivalent single degree of freedom system with added linear viscous damper Figure 1: Single-degree-of-freedom system in Problem 1. Please…
A smooth sphere of weight Wis supported by a string fastened to a point C on sphere and point A on the smooth vertical wall. The sphere is in contact with the wall at point B as shown in figure. If the length of the string AC is equal to the radius of sphere, then sum of magnitude of tension (T) in the string and reaction (R) on the wall is. W. (Round off two decimal places). A B Wall String Sphere Length of string AC = Radius
1. Consider a water jet having a diameter of D = 1 cm and a flow of Q = 1 L/s. The jet is deflected by a fixed plate which is inclined at an angle of 50° from horizontal. a) Determine the velocity vx in the x-direction in m/s. b) Determine the velocity vy in the y-direction in m/s. c) Determine the resultant force Fx on the plate in the x-direction in N. d) Determine the resultant force Fy on the plate in the y-direction in N. e) Determine the combined resultant force F on the plate in N. 1 L/s 50° V = 6 m/s
The block slides at a constant speed on a surface with friction. In each case, the water jet has velocity 50 m/s and cross-sectional area 5 cm2, and the block has velocity 25 m/s. In case (a), the jet is deflected to an angle of 60° from horizontal relative to the block, as shown. In case (b), the jet is deflected 180°. Calculate the friction force in each case. Apply both a moving Reference Frame (RF) and a fixed RF. Use the VSM. Check that both RFs give the same friction force for a given case. (We would not expect the two cases to have the same friction force!) Density of water is 1000 kg/m3. All jets are open to the atmosphere. case (a) 60° case (b)
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 120N/m 300 N 300 N-m 200 N 100N/m Im B 4m C Im DIm E 4m 1m G 400 N¬m
Try to calculate the Fixed-end Moment (FEM) shown in the figure below.
STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. Please write the complete solutions and answer all the subquestions. a. Graph the shear and moment diagram b. Find the value and location of Maximun Shear and Maximum Moment c. Give short explanation/analysis on the shear and moment diagram. (3 sentences or more)
A brass disk of radius 0.7 ftft and weight 459 lblb sits in a right-angle groove made of granite. The disk makes contact with the groove at AA and BB and the coefficient of static friction at both points are μS=μS= 0.39 A couple moment of MM is applied to the disk as shown.
statics of rigid bodies
In doubly reinforced beams, compressive reinforcement is used: Select one a. to reduce long term (creep) deflections. Ob. to support the stirrups. C. for all what is mentioned in the other items Od. to increase the strength of a limited cross-section.
Consider the beam shown in Figure 2 (a) with the cross-section shown in figure 2 (b). a) Determine the reactions, bending moment and shear force along the beam AD and sketch the corresponding diagrams, 2 kN/m В 400 mm 工 130 mm 1.5 m 400 mm 20 mm 180 mm -2 m .1 m (а) (b)
Consider the beam shown in (Figure 1). EIEI is a constant. Suppose that www = 19 kN/mkN/m.