295 m1:35-2605Pz = 40 klagageK-0.422=0.113110 m?/sK=1dpipe:3150 mmAir15@mと-0-046 mmwaterAscrubberK=0.9300m->The industrial scrubber B consumes water et the rateof ol m³ls. If the pipe diameter is 15omm e E =0046 mmwhat shoul d the pressure Pi be ??

Bournallis Equation is based on conservation of energy It means that the total energy of the system…

Answered: Pz= 40 k 1. K=0.4 2-0.113X10°m?/s d…

Engineering

Mechanical Engineering

Pz= 40 k 1. K=0.4 2-0.113X10°m?/s d pipe - Iso mm Air B %3D 15@m water E=0.046 mm scrub K20-4T K=0.9 300m->

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Complete solutions, pls! TY!
1. Referring to figure 37.90, a rectangular duct with cross sectional measurements of 20 inch × 11 inch will be the equivalent of a round duct with diameter of.
for line Pife i Daen Daimetel omm Q = 1. 6 LI m.n Dhact = 26 Cm Determing %3D BQ m/s m/s (3) oh theo Re at tube length To cm
Problem -1 A tank is initially empty. A liquid with p = 62.4 Ibm/ft is poured into the tank at a constant mass flow rate of mi = 7 lbm/s. The tank has cross-sectional area A = 0.2 fe, and the fluid in the tank has a %3D variable height H(t). There is a hole at the bottom of the tank. The fluid flows out of the tank at a rate proportional to the fluid height: rme = kH, where k= 1.4 lbm/ft/s. Find H(t). A sketch is given in Fig. P.1. Figure.P.1: Sketch of tank filling problem
Dimensions of a hydraulic cylinder are Dsore=178 mm, Dpiston Rod=50 mm. For a 1,6 m/min extracting speed; Determine the supply flow rate (It/min) Q= ? It/min
9:42 A O P • Done Question 1 Ta. You want to draw water from a stream running down a hill behind your house at a rate of 0.003m/s. To hand you have 30m of commercial steel tubing of inside diameter 30mm. At what vertical level above the house should you dam the stream to draw off the water? b. A simple, vertical U-tube manometer is used to measure the difference bētween two gas pressūrēs. Write down an equation for the pressure difference in terms of the difference in the level of the fluid in the manometer. Describe briefly, with the help of diagrams, two modifications to the basic design which offer greater sensitivity to small pressure differences. Give equations for their use. c. An extractor fan draws air from a room and delivers it to the surroundings through a 5m long circular duct of diameter 0.1m. The friction coefficient for the duct flow is 0.002. The fan characteristic, relating its total pressure rise, AP (Nm-2) to the volume flow rate is: AP = 103-7x10*Q 2. What is the…
A pump, for which the characteristic curve is shown below, is used to pump water from a canal into a dam. The pump is mounted 2.0 m above the water level. There is a 50 mm PVC pipe connected to the suction side of the pump, and a 40 mm PVC pipe connected to the discharge side. The total length of pipe on the suction side is 8 m, and there is a strainer (K = 20), a non-return valve, a 90° elbow and a fully open gate ball valve in the suction line. Another fully open gate valve, and two 90° elbows are mounted in the discharge line. The total length of the discharge line is 60 m, and the discharge pipe outlet is 4 m above the pump. You may assume a water temperature of 25 °C. Determine: (a) The flow rate through the system(b) The required fluid power(c) The efficiency of the pump(d) Whether the pump will cavitate or not.
Please show step by step solution thank you
i need the answer quickly
Problem 01 Find the least number of 150 mm diameter pipes required to transmit 170 kW to a machine 3.2 km from the power station, if the efficiency of transmission is to be 90 per cent and f= 0.0075. The feed pressure is 4800 kN/m². Collutate of Pipes required efficiency= Problem 02 A turbine of efficiency 78% is 750 m lower than the supply water source. The pipe supplying the turbine with water is 200 mm in diameter and 4,5 km long. Take f=0,008 and determine the maximum power output that can be expected from the turbine. Problem 03 A pipeline is 1800 m long and 375 mm in diameter, and supply head at inlet is 240 m. A nozzle with an effective diameter of 50 mm is fitted at the discharge end and has a coefficient of velocity of 0,972. If for the pipe is 0,005. (a) The velocity of the jet (b) The discharge (c) The power of the jet C1Reg
How to calculate permeability according to silica bead characxteristics without knowing pressure drop? silica diameter: 2.5mm Inlet mass flow rate: 0.3m^2/min Inlet Temperature: -10 degree C
I need answer in handwritten