Pure aluminium is poured into a sand mold. The metal level in the pouring basin is 203.2 mm above the metal level in the mold, and the runner is circular with a 7.62 mm diameter. What is the velocity and the rate of flow of the metal into the mold? Is the flow turbulent or laminar? Note that pure aluminum has a density of 2700 kg/m3 and a viscosity of 0.004 Ns/m

Q: A diesel component steel plate has a surface area of 200 in2 with a thickness of 0.002 in. Determine…

A: Given data as per the question Surface area of plate=200 in2=1290.32 cm2thickness =0.002 in=0.00508…

Q: Question 2 A cylindrical container has a diameter of 1.2 m and is open at the top. The container is…

A: x = 0.5 mtrRadius R = 0.6 mtrBefore water being splitted vsplit = 0Initial volume =…

Q: 6- In a sand-casting operation, a part whose side view and top view are shown below is to be made.…

A:

Q: kindly

A:

Q: What do you call this molten material

A: When lava cools, it turns into volcanic rock and volcanic glass. A powerful volcanic eruption…

Q: A true centrifugal casting operation is to be performed in a horizontal configuration by Durban…

A:

Q: 1. Define viscosity of a fluid. 2. What is the defining characteristic of a Newtonian fluid? 3. Wood…

A: Let us discuss above questions.   As per Bartleby guidelines we are abide to solve only first 3…

Q: shape factor for a casting in the form of an annular cylinder

A: Given; The shape factor for a casting in the form of annular cylinder ?If outside diameter, D=25…

Q: surface (c) trapped near the mean radiu

A: given: In centrifugal casting, the lighter impurities are (a) uniformly distributed (b) forced…

Q: Determine angle of repose for the given powder sample having the height of the powder pile=5inches…

A: Given data: h=5 inr=d2=13 in

Q: A thin steel disk of an oil separator of 100mm outside diameter is shrunk onto a solid steel shaft…

A: Solution: Given Data: dD=100 mmds=20 mmN=100000 rev/minE=210 GPaμ=0.3ρ=7850 kg/m3   To Find:…

Q: 12.Silica sand has which one of the following compositions: (a) Al2O3, (b) SiO, (c) SiO2, or (d)…

A: 12. Silica is SiO2 (option c) 13. Misrun is a casting defect in which casting cavity not filled…

Q: Gates are incorporated into molds in order to: O improve polymer flow and reduce defects. open or…

A: Topic : moulding

Q: The passageways in the parting plane through which molten metal flow is regulated are known as:…

A: Option (3) correct

Q: A flat plate is being injection molded using PLA (a = 0.075 mm2/s) at a temperature of 110°C. The…

A: Given, Temperature conductivity rate, a=0.075mm2/scooling time,t=15secθ=80°Cθs=40°Cθo=110°CTo…

Q: EX.2/The downsprue leading into the runner of a certain mold has a length = 175 mm. The…

A: H=175 mm or H=.175 mA=400 mm2or A=400×10-6 m2Mold cavity volume V=.001 m3

Q: What is the appropriate way to determine the information inside a sand casting? Explain that. NS. If…

A: Sand Casting:- Mould material-sand Binders- clay, silica, corn flour For making a sand casting a…

Q: 2. A mold sprue is 180 mm long, the cross-sectional area at its base is 2.4 cm?. The sprue feeds a…

A:

Q: 2. A 10-inch x 10-inch x 0.75-inch plate casting is produced with a steel alloy with p = 0.28 lb/in³…

A:

Q: Why is the feeder used in the casting process? What is its significance and how should it be…

A: feeder used in the casting process to avoid shrinkage porosity. Feeder: Feeders are added…

Q: Discussions: 1- How the effect of temperature on Reynold's number? 2- Show that Reynold's number is…

A: Reynold number is the dimensionless number or it is the ratio of the inertia force to the viscous…

Q: Sharp corners and angles should be avoided in mold design, since they are sources of stress…

A:

Q: casting (b) Investm

A: given: For casting of turbine blades made of high temp and high strength alloys, the most suitable…

Q: A component is sand casted in pure aluminum. The level of the metal inside a pouring basin is 215 mm…

A: The gating system in casting is a metal pouring mechanism that directs molten metal into the mould…

Q: net buoyancy force

A: Given; An aluminium alloy; Density,ρ=2600 kg/m3Casting is to be produced a cylindrical hole of,…

Q: A component is sand casted in pure aluminum. The level of the metal inside a pouring basin is 215 mm…

A:

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

A:

Q: A cylindrical riser with diameter-to-length ratio=1.5 is to be designed for a sand casting mold. The…

A:

Q: Calculate the heat you need to take/give to make all 1 kg of mercury at a temperature of 357⁰C at a…

A: To find  The heat required to take from1 kg of mercury decrease temperature from  357°C to -39°C.…

Q: (a) Plot the specific heat of water versus the water temperature for temperatures ranging from 80 to…

A: Initially the variation of specific heat of water ranging from 80°C to 120°C has to be plotted. Then…

Q: Determine the time required

A: Given data;   A mould has downsprue whose;   length (h)=20 cm=0.2 m  Cross-sectional area;…

Q: expected time of solidifications

A: Given; Two cubical casting of the same metal and sizes of;⇒  2cm and 4 cmIf the smaller casting…

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.