Review ProblemsThe extrusion die for a polyethylene parison used in blowmolding has a mean diameter of 18.0 mm. The size of the ringopening in the die is 2.0 mm. The mean diameter of the parison isobserved to swell to a size of 21.5 mm after exiting the dieorifice. If the diameter of the blow molded container is to be 150mm, determine (a) the corresponding wall thickness of thecontainer and (b) the wall thickness of the parison.

Answered: Image /qna-images/answer/7c4a9513-b578-4213-a0dc-4969da743abf.jpg

me extrusion die for a polyethylene parison used in blow olding has a mean diameter of 18.0 mm. The size of the ring pening in the die is 2.0 mm. The mean diameter of the parison is bserved to swell to a size of 21.5 mm after exiting the die orifice. If the diameter of the blow molded container is to be 150 mm, determine (a) the corresponding wall thickness of the Container and (b) the wall thickness of the parison.

me extrusion die for a polyethylene parison used in blow olding has a mean diameter of 18.0 mm. The size of the ring pening in the die is 2.0 mm. The mean diameter of the parison is bserved to swell to a size of 21.5 mm after exiting the die orifice. If the diameter of the blow molded container is to be 150 mm, determine (a) the corresponding wall thickness of the Container and (b) the wall thickness of the parison.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As the lead engineer for a LPG storage project, you are overseeing the design of pressure vesselssuch as those shown below. Identify which test (or tests) is mostsuitable to pick a material and thickness for the spherical shell of the pressure vessel. Why these are the relevant tests. Explain what information these tests provide and why it is important to determining material and thickness.
Which of the following are reasons why injection molding of thermosets is more difficult than injection molding of thermoplastics (two best answers): O allowances must be made for cross-linking of thermosets O barrel temperatures must be hotter for thermosets O cycle times are longer because of curing thermosets are denser O two injection units are required
Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s') Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175
May I have help with this please?
Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
why is the answer B?
10. A compound tube is formed by shrinking together two tubes with common radius 150 mm and thickness 25 mm. The shrinkage allowance is to be such that when an internal pressure of 30 MN/m² (300 bar) is applied the final maximum stress in each tube is to be the same. Determine the value of this stress. What must have been the difference in diameters of the tubes before shrinkage? E=210 GN/m².
Consider a single screw melt extruder with the following dimensions: D = 6.0 cm, L = 60.0 cm, H = 0.6 cm, W = 6.0 cm & helix angle of 17.4º. The capacity at open discharge is 10 kg/hour and the viscosity of the polymer melt is 500 Ns/m?. a. Determine the pressure when Q = 5 kg/hr. b. Determine the pressure when a round die of diameter 3.00 cm and length 10.0 cm is attached to the extruder.
In the event that the weight value as well as the discharge value were fixed and the shapes of the targets with different angles were changed in the jet extrusion impact experiment, which targets give greater value to (fy) and why? Proving it mathematically?
A hydraulic press for compacting powdered PRACTICE samples has a large cylinder which is 10.0 cm in diameter, and a small cylinder with a diameter of 2.0 cm (Fig. 9). The piston of the small cylinder is attached to the midpoint of a lever that is hinged at point C as shown in the figure. The sample, which is placed on the large cylinder, has an area of 4.0 cm?. What is the pressure on the sample if 350 N is applied at the end of the lever? (Giancoli, 2014) F2 350 N Sample- F Hydraulic. fluid 10.0 cm Small cylinder -2.0 cm
polymer operations
Provide an sustanable and economical block flow diagram of rigid polyurethane foam from lignin.