PS-1. Determine the internal torque at cach section and show the shear strew on differential volume elements located at A. B,C,and D. O Nm 300 Nm

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3).

A: Given data, TE = Torque at E = -11 N-m (Cross-section is twisted in clockwise direction from right…

Q: 2. Determine the clamping force on the bolt and reactions at pin A for the pliers shown.

A: It is required to determine the force on the bolt and reactions at pin A, given that the applied…

Q: For the shaft shown in the figure below, compute the angle of twist of pulleys B and C relative to…

A:

Q: 3 in The following data apply to the C-clamp: a. The screw is ACME with ¾" Diameter b. Coefficient…

A: Given:W=1000 lbcoefficient of thread friction,f=0.12coefficient of collar friction,fc=0.23Mean…

Q: Required information 54 mm 44 mm G Te 46 mm To 40 mm Under normal operating conditions, the electric…

A: Note- Hi, as per the guidelines, we can solve up to 3 subparts for you, For the rest of the…

Q: In the gear system of Figure 4, a torque of 5 N-m is applied on gear E. Shaft (1) and shaft (2) are…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

A:

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

A:

Q: below. Determine: (1) the torque in shaft c-d to the nearest in-lb and (2) the angle of twist at…

A: To determine the torque in the shaft and the angle of twist at a pointgivenradius of gear b=radius…

Q: A pinion having 40 teeth drives a gear having 80 teeth. the profile of the gear is involute with…

A: Pinion Teeth TP=40 Gear Teeth TG=80 Pressure Angle ϕ=22° Module m=12 mm Addendum =14 mm

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A:

Q: Please show complete work in handwritten format. Don't use chatgpt,If you use Chatgpt it will get a…

A:

Q: -2x Criven the shape above, Find the location of the Controid. Show all work.

A: Here, four shapes are visible so, No Shape Ai Xi Yi AiXi AiYi 1 Semi circle 5654.87 60 0…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm…

A:

Q: The composite shaft shown consists of two steel pipes that are connected at flange B and securely…

A: find the torque in pipe (1).

Q: ed force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft…

A: The force transmitted on gear A is .The pressure angle given for gear A  is .The pressure angle…

Q: A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long…

A: Given, Speed of the shaft N=200rpm Length of the shaft=1m Diameter of the shaft=50mm Power acting on…

Q: A 2in diameter shaft is made of aluminum 2014-T6, and has a torque of 1/2T, -T and 2/3T respectively…

A: Write the given data. D=2 inL=12 inFOS=3θ=0.1 radτ=42.06 ksi Write the equivalent torque on the…

Q: 4. A shaft for an automobile transmission has 10 splines with the following dimensions: D = 1.25 in,…

A: Given data ,No of splines Length Diameter

Q: Required information A torque T-130 N-m is applied to the shaft EFG, which is running at constant…

A: Given-Information:- Torque, T = 130N-m Pitch diameters, a = 120 mmb = 200.004 mmc = 100 mm Pressure…