Provide complete solution and box your final answer with appropriate unit. 1. What is the total length of the course XY if the rear tape-man holds exactly holds 9 pebbles and 3 pins after measuring the course XY? Assume that one tape length is equivalent to 30m

Provide complete solution and box your final answer with appropriate unit. 1. What is the total length of the course XY if the rear tape-man holds exactly holds 9 pebbles and 3 pins after measuring the course XY? Assume that one tape length is equivalent to 30m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the Venturi meter and manometer installation shown, derive an expression relating the volume rate of flow with the manometer reading. Denote p as the density of fluid and pm as the density of the fluid in the manometer. Ans: Q = A₂[ {(2gR) (pm/ p-1)}/(1- (D2/D1)^4) ] ^1/2 Datum D1 z1 z2 R ↑
Question 5 1 pts A pipe system has a discharge of 0.0316 m3/s with n = 0.013. Find the total loss of head between A and F. in m Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 Pipe Length (m) Dia (mme) AB 180 150 BC 60 150 BE 150 150
Do not round off in between solutions and box your final answer. Correct answer should be 130
يجوز تتحمل اكثر منج
Cbih
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Two 10° wedges of negligible weight are used to move and position the 380-lb block 10 W Knowing that the coefficient of static friction is 0.25 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges. The smallest force that should be applied to one of the wedges is[ lb-
Calculate the volume V of the solid generated by revolving the 65-mm right-triangular area about the z-axis through 180°. Assume a = 65 mm, b = 40 mm. a dod Answer: V = i mm³
1. A tape measure 1.25 cm wide x 0.40 mm thick having an elastic modulus E = 1.6 GPa is used to measure the lake frontage of a home lot which is priced at $50,000/m of frontage. In making the measurement, the tape is pulled tight and straight with 20.0 N of force. a. What value would the tape measure indicate for an actual length of 100.0 m? (The scale marks or graduations were printed on the tape under zero load.) b. Who has the advantage due to the elasticity of the tape measure, the buyer or the seller? Explain.
the value of A=382.3 , E=120 , B, 25 , AND D=9
21 B -32 C D Z2 ▼ Part B As shown, a system of cables supports a bucket. (Figure 2) The dimensions in the figure are as follows: ₁ -5.25 ft, 2 = 1.40 ft. y₁=2.20 ft. 3/2=4.50 ft. 2₁ = 3.25 and 22 = 2.30 ft. If the bucket and its contents have a combined weight of W = 11.5 lb, determine TA. TB. and Tc. the tensions in cable segments DA, DB, and DC, respectively. Express your answers numerically in pounds to three significant figures separated by commas. ▸ View Available Hint(s) TA TB.TC Submit 175) ΑΣΦ | 41 Previous Answers Provide Feedback X Incorrect; Try Again; 4 attempts remaining. Part C Complete previous part(s) vec 6 0 BOA ? lb
Consider (Figure 1). Figure Vo 00 6 m 3 m ▼ Part A Determine the minimum initial velocity vo at which the ball must be kicked in order for it to just cross over the 3-m high fence. Express your answer using three significant figures and include the appropriate units. v0 = Submit Part B 00 = μА Submit Value Request Answer Units Determine the corresponding angle o at which the ball must be kicked. Express your answer in degrees using three significant figures. AΣ vec Request Answer **** *** ? ***** ***** ? O
Directions: Kindly solve numerically what is asked in the following problems using the following techniques: for number 3 (Secant Method-SM). Kindly upload the excel file as your solution file (with proper tabular presentation and highlighted answers of up to 4 decimal places only). Use a tolerance of 0.0005. Initial estimates will be at your discretion.