Properties: b1 = 300 mm • b2 = 180 mm . • d1= 250 mm • d2 = 350 mm • fc = 28 MPa B fy=414 MPa . eccentricity = 500 mm 155 55 6-20mmø d₂ 120 155 b₁ 4-28mmø Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in KN 4. Moment Capacity in kN-m b2

Properties: b1 = 300 mm • b2 = 180 mm . • d1= 250 mm • d2 = 350 mm • fc = 28 MPa B fy=414 MPa . eccentricity = 500 mm 155 55 6-20mmø d₂ 120 155 b₁ 4-28mmø Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in KN 4. Moment Capacity in kN-m b2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the exact in the figure tensile strength = 8000 N/cm^2 compression safety = 3000 N/cm^ 2 calculate the largest Mx moment that the section can carry. S-2) 2.5 3 как 2.S cm pomk CM AA 3.5 3.5 3 CM x<- vy 18cm 15 Cm 5cm
21. A Single rivet lop joint is to commect 12 mm thick plates by providing 20mm dia. rivet at somm pitch. determine the strength of the joint and joint efficiency. Take working stress in shear in rivets = 80 N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates. = 150 N/mm².
Please show answer clear and easy to read and explain the answer if possible thankyou very much in advance
Figure Q3 shows the copper shaft subjected to the axial loads. Determine the displacement of end A with respect to end D. The diameters of each segment are daB = 75mm, dâc = 50mm, and dcp = 25mm. Take Ecu 3D 126GPa. (C02, СЗ, РО1, WP1) %3D 1250mm 1875mm 1500mm 10kN 30KN 5kN C 15KN 10kN A В
determine the reacction of th beam show in fig by using consistante deformatiom method . use the redundants Cy and Ey
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Need asap pls. Thanks.
B4
Refer to the illustration below. f=28 MPa, fy= 400 MPa a. Determine the ultimate axial capacity of the spiral column b. Determine the maximum spiral pitch c. Determine the clear spacing between the main reinforcements 6 #29 360 mm 70 mm 70 mm 500 mm 3.
I. N • O P M E;Y7 Z H.W. for fatigue stresses... Q1) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L), if the stress at the fillet equal to the half stress at the center. de6.25 62.5 -O- 50 -375 375 Fillet Fillet All Dimensions in mm Center Fig(1) Q.) In Fig.(2), the shaft is subjected to reversed loads, F = 7 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the required length (L), if the stress at the fillet equal to the stress at the center. F 2700 N P.1350 N P.1350 N 50 62.5 1500 - - Fillet Center Fillet Al Dimensions in mm Fig(2) Q.) In Fig.(3), the shaft is subjected to reversed loads, F = F 2700 N and P = F 1350 N, where these two loads vary at the same time. Find the diameter (d), if the stress at the fillet equal to the stress at the center. F- 2700 N * 10 P.+1350 N P-1350 N d. 1.6 d 500- - 1500 - 500 Fillet Center Fillet All Dimensions in mm Fig(3) Q.) In the Fig.(4) shown below, a machine member is…
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 What will be the maximum weight of cylinder that can be put as shown in the figure below if the maximum stress at cable is FN mPa? Note: Round off your answer in two decimal places.
Answer 15&16