Procedure: Experiment 1. Prepare 50 mL of an aqueous solution of 0.10M NaHCO3 (sodium bicarbonate, baking soda). 1. Determine how many grams of sodium bicarbonate are required. Show all steps for this calculation, using dimensional analysis with units clearly identified. 2. Prepare this aqueous solution, using a volumetric flask for the precise final volume measurement. It is not a problem to use tap water.

Procedure: Experiment 1. Prepare 50 mL of an aqueous solution of 0.10M NaHCO3 (sodium bicarbonate, baking soda). 1. Determine how many grams of sodium bicarbonate are required. Show all steps for this calculation, using dimensional analysis with units clearly identified. 2. Prepare this aqueous solution, using a volumetric flask for the precise final volume measurement. It is not a problem to use tap water.

Chemistry: Principles and Reactions

8th Edition

ISBN:9781305079373

Author:William L. Masterton, Cecile N. Hurley

Publisher:William L. Masterton, Cecile N. Hurley

Chapter3: Mass Relations In Chemistry; Stoichiometry

Section: Chapter Questions

Problem 23QAP

See similar textbooks

Similar questions

The units of parts per million (ppm) and parts per billion (ppb) are commonly used by environmental chemists. In general, 1 ppm means 1 part of solute for every 106 parts of solution. Mathematically, by mass: ppm=gsolutegsolution=mgsolutekgsolution In the case of very dilute aqueous solutions, a concentration of 1.0 ppm is equal to 1.0 g of solute per 1.0 mL, which equals 1.0 g solution. Parts per billion is defined in a similar fashion. Calculate the molarity of each of the following aqueous solutions. a. 5.0 ppb Hg in H2O b. 1.0 ppb CHCl3 in H2O c. 10.0 ppm As in H2O d. 0.10 ppm DDT (C14H9Cl5) in H2O
A solution is 0.1% by mass calcium chloride. Therefore, 100. g of the solution contains g of calcium chloride.
What does it mean when we say that a 200-mL sample and a 400-mL sample of a solution of salt have the same molarity? In what ways are the two samples identical? In what ways are these two samples different?
A student weighs out a 4.80-g sample of aluminum bromide, transfers it to a 100-mL volumetric flask, adds enough water to dissolve it, and then adds water to the 100-mL mark. What is the molarity of aluminum bromide in the resulting solution?
A throat spray is 1.40% by mass phenol, C6H5OH, in water. If the solution has a density of 0.9956 g/mL, calculate the molarity of the solution.
a 50.0 mL sample of aqueous sodium chloride was analyzed according to the experimental procedure in part E and the following data were obtained. mass of evaporating dish: 37.628 g mass of evaporating dish + solution: 86.623 g mass of evaporating dish + solid NaCl: 41.133 g A) Calculate the percent by mass NaCl in the solution. B) Calculate the Molarity of the solution. C) Calculate the molality of the solution.
At a particular temperature, suppose that 24.4 g solute is added to 50.0 g water and, after mixing, 0.3 g of the solute remains undissolved. What is the solubility of this solute at this temperature in grams per 100 g of water? (Enter in standard notation with one digit after the decimal point) Type your answer......
Please answer in correct question format to use the available options below the question.
Weigh accurately 4.0 g of sodium chloride into a 250cm3 volumetric flask. Using a wash bottle add about 200cm3 of distilled water. Stopper the flask. Shake vigorously for three minutes. Remove the stopper for a second then continue to shake for about another two minutes until all the solid has dissolved. Add more water slowly upto exactly the 250 cm3 mark. 1.Calculate the number of moles of sodium chloride present in: (i) 4.0 g (ii) 250 cm3 solution in the volumetric flask. (iii) one decimeter of solution
Why are volumetric flasks used to prepare solutions for analysis? Question options: All of the above. They are specifically designed to deliver a specific volume of solution. Their shape provides better quality data. They are specially designed to contain a specific volume of solution. (on assignment I selected "all of the above which is evidently incorrect.. thanks for help!)
PLEASE FILL IN THE TABLES BELOW. THANK YOU!
3. A student neutralized 25.0 cm³ of sodium hydroxide solution with 0,6 student carried out the experiment three times and obtained the following results. Experiment 3 Experiment 1 Experiment 2 Volume of Acid 19.90 17.30 17.40 Used/ cm3 (a) The student calculated the volume of acid used by calculating the average of the volume of acid used in Experiment 2 and Experiment 3. Explain why the first reading was not considered. (b) Calculate the amount (moles) of 0.6 moldm³ sulfuric acid in the average titre value used to neturalise the sodium hydroxide. (c) How many moles of sulfuric acid react with 1 mole of sodium hydroxide? (d) What amount (moles) of sodium hydroxide were there in the 25 cm³ sample?