PROBLEMS: 1.) The single 200mm x 10mm steel plate is connected to a 12mm thick steel plate by four 16mm diameter rivets as shown. The rivets used are A502, Grade 2, hot driven rivets. The steel is ASTM A36 with Fu = 400MP.. Find the other properties needed in the tables provided in the lecture and references. Determine the value of P in all possible modes of failure and the safe value of P that the connection can resist. 200 mm 50 mm 100 mm 50 me 35 mm 4- 16mm o 100 mm

PROBLEMS: 1.) The single 200mm x 10mm steel plate is connected to a 12mm thick steel plate by four 16mm diameter rivets as shown. The rivets used are A502, Grade 2, hot driven rivets. The steel is ASTM A36 with Fu = 400MP.. Find the other properties needed in the tables provided in the lecture and references. Determine the value of P in all possible modes of failure and the safe value of P that the connection can resist. 200 mm 50 mm 100 mm 50 me 35 mm 4- 16mm o 100 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A No. 8 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it was found that the specimen yielded at a load of 60,000 lbs and fractured at 75,000 lbs. Determine the following: a. Tensile stresses at yield and at fracture. b. Estimate how much increase in length would occur at 75% of the yield stress in a 16-in. gauge length.
A flanged bolt coupling is used to connect a solid shaft 100 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 53 MPa, how many 16 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule -- so our answer here must be rounded to the NEXT whole number.
My student number is 202010237
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
A storage tank of air, 30 inches in diameter, is to withstand an internal pressure of 180 psi with a design factor of 3.5 based on ultimate stress. The steel has the strength equivalent of C1020 annealed and the welded joints should have a relative strength of 92%. Note: ultimate stress of for annealed C1020 steel is 50 ksi. Compute for longitudinal stress of the tank. a.13, 171 psi b.13, 786 psi c.12,893 psi d.12,860 psi
A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 100 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 102 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P. High-density polyethelene (HDPE) rod Answer: P = i P kN
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
Please ACI code , not IS code
A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm in outside diameter and 80 mm in inside diameter. If the allowable shearing stress in the shafts and in the bolts is 58 MPa, how many 16 mm-diameter steel bolts must be used on a 300 mm-diameter bolt circle so that the coupling will be as strong as the weaker shaft? This is an exception to our two decimal rule -- so our answer here must be rounded to the NEXT whole number. Previous Next ENG US
Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed.
Problem 1 A steel connecting rod with length of 6 meters and is to be subjected to a tensile load of 70 KN. A. What will be the diameter if the total elongation is not to exceed 4 mm. B. Choose a stainless-steel material based on yield strength and dead load.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt