%£9 lI.4G11:91st class / 2021- 2022PROBLEMS1 - A ( 200 N ) weight of the block shown in fig. issupported by a pin and bracket at ( A ) and by a cable( BC ). Determine the reaction at ( A ) and the tension30in the cable0.752 - The 200-N force produces a torque (moment) of40 N.m about the axis of the bolt in order totighten the hexagonal nut. Find the forcesbetween the smooth jaws of the wrench and thenut if contact occurs at the corners A and B ofthe hexagon.3 - The pin at A can support a maximum force of 3.2 KN .What is the coresponding maximum load L which canbe supported by the bracket ?4 - A block placed under the head, of the claw hammer asshown greatly facilitates the extraction of the nail. Ifthe 200-N pull on the handle is required to pull the nailcalculate the tension T in the nail and the magnitude Aof the force exerted by the hammer head on the blockThe contacting surfaces at A are sufficiently rough toprevent slippingAlamarah University CollegeDepartment of MedicalInstrumentation Tech.Subject: Mechanicslecturer: Eng. Abrar Ameen1st class / 2021- 20225 - The ring supports the 1000-N load and is held inposition by the two cables attached to vertical wallsFind the tensions T, and T; by at least two differentways.1000 N6 - The cable from A to B is 6 m long and supportsthe 100-kg crate from the small pulley .Calculate the tension T in the cable.100 keII

Answered: Image /qna-images/answer/ef56dfc7-57b4-4201-94dd-e5db7c443a22.jpg

Answered: PROBLEMS 1 - A ( 200 N ) weight of the…

PROBLEMS 1 - A ( 200 N ) weight of the block shown in fig. is supported by a pin and bracket at ( A ) and by a cable ( BC ), Determine the reaction at ( A) and the tension in the cable.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A T- shaped bracket supports the four loads shown. Determine the reactions at A and B if a= 120 mm
4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B, C, and D. If the tension in wire AC is 920 lb, determine the vertical force P exerted by the tower on the pin at A.
Answer the following question: 1. Determine the vertical and horizontal components of the reactions at pin A and the tension developed in cable BC used to support the steel frame.
answer is B=14.528lb D= 14.58lb F= 3lb, but I need help to get to them 1. For the frame below a. Use a free body of the full structure to find the reactions at Pin A and Roller B. b. Determine the magnitude of the forces on pins B, D, and F. Show your ree oeY diagrams. 30 in-lb 10 lb 6" 7" 4" 3" 4" 3" 1. 1.25"
The cable shown supports a girder which weighs 850 lb/ft. Determine the tension in the cable at points A, B, and C.
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between 2 wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. (a) Determine the magnitude of the force in member CD. Is the member in tension or compression? (b) Determine the support reactions at A. (c) Determine the unstretched length of the spring EF given a spring constant of 150 kN/m. 60 mm 1130 mm 60 mm 245 mm D 220 mm F 260 mm E B 165 mm 90 mm F = 4200 N
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. (a) Determine the magnitude of the force in member CD. Is the member in tension or compression? (b) Determine the support reactions at A. (c) Determine the unstretched length of the spring EF given a spring constant of 150 kN/m. 130 mm 60 mm 245 mm 60 mm D A 220 mm F 260 mm C EB 165 mm 90 mm * F = 4200 N
The solid bar shown is supported by simple bushings that exert reaction forces on the bar. Determine the reactions at supports A, B, and C.
The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal (slider) bearing at D. At the journal bearing D, the mome support reactions and the force support reaction along y-axis are zero. The 2-kip force and the 6 kip-ft couple-moment are parallel to z-axis and applied at point B Determine the tension in the cable AE and the support reactions at O and D. A 4 ft X MEST Z 6 kip-ft 2 ft B 2ft 2 kips 3 ft [ 1 kip = Lo = 1000 lb. 1 E 14 ft y