The given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A-L, A-B, and B-K are as indicated in the table. If the vertical reactions at A and G are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. What is the computational internal force of Member B-K?" 8 kN 4 kN to C. E 3 m K J 1 12 m, 6 @ 2 m Member A-L А-В Experimental 13.533 14.680 0.012 Computational Percent Error В-К O 13.334kN O 15.781KN O 14.908kN

The given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A-L, A-B, and B-K are as indicated in the table. If the vertical reactions at A and G are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. What is the computational internal force of Member B-K?" 8 kN 4 kN to C. E 3 m K J 1 12 m, 6 @ 2 m Member A-L А-В Experimental 13.533 14.680 0.012 Computational Percent Error В-К O 13.334kN O 15.781KN O 14.908kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 656 kN. (a) Determine the magnitude of the pin reaction at A in kN. (b) Determine the magnitude of the pin reaction at B in kN. (c) Determine the magnitude of the pin reaction at C in kN.
Question 2: The framed structure illustrated in the diagram consists of identical right angled triangles of base 2 metres and is symmetrical in design with angles as shown and all loads in kN. The frame is supported at pins 8 and D. (a) Determine the magnitudes of the support reactions at pins Band D; (b) Use the method of joints to determine the type (tension or compression) and the magnitude of the force in each member of the frame. 15 kN 15 kN 45° 45° H IG 20 kN
4.) The uniform 4-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is attached to the midpoint G of the rod as shown in the figure. The rod leans against a frictionless vertical wall at B. Determine the reactions at A and B and the tension in cord CG. [Answer: T = 20.8 N, Ax= -14.7 N (down), Ay= 29.4 N, Az 11.0 N, B= 29.0 N, where the positive answer indicate the reaction goes in the positive direction of the respective axis and vice versa] Hints: Note the given mass from which you need to calculate weight. IF G is is the midpoint of the rod, then the x, y, z coordinates of that point can be taken to be half the x,y,z components of the position vector FAB 150 mm, B 400 mm 0 150 mm 600 m G
Needs Complete solution with 100 % accuracy.
Two bars connected by a sliding block are shown in the figure. If the effect of friction is not taken into account, perform the following operations: 1.1 Draw the Free Body Diagram (F.B.D.). (1.0 point) 1.2 Determine the moment Ma necessary to keep the system in equilibrium. (1.0 point) 1.3 Determine the magnitude of the reaction at support A. (1.0 point) 1.4 Determine the magnitude of the reaction at support B. (1.0 point) 1.5 Determine the magnitude of the reaction at joint C. (1.0 point)
Pls answer with complete solution. Thanksss!!
Please solve via Handwritten, If not at least draw a free body diagram in a separate sheet and label all the points.
answer is B=14.528lb D= 14.58lb F= 3lb, but I need help to get to them 1. For the frame below a. Use a free body of the full structure to find the reactions at Pin A and Roller B. b. Determine the magnitude of the forces on pins B, D, and F. Show your ree oeY diagrams. 30 in-lb 10 lb 6" 7" 4" 3" 4" 3" 1. 1.25"
In the carrier system below, the AB console is fixed to the wall from point A and a pulley with a radius of 30 mm is attached to point B. Find the reactions that will occur at the support point A of the cantilever, taking into account the rope loads applied to the pulley.
Compute the total reactions at A and B for the truss shown in figure. 30 KN C 60 KN 3m D 3m E 4 m 120 KN 4m G B 4 m H 50 KN
i need the answer quickly
For the structure loaded as shown in the figure, find the reactions at A and D.