PROBLEM The mechanism shown below is used in a distribution center to push boxes along a platform and to a loading area. The input link i driven by an electric motor, which, at the instant shown, has a velocity of 25 rad's and accelerates at a rate of 450 rad/s. Knowing that the input link has a length of 250 mm, determine the instantaneous acceleration (m/s) of the end of the input link in the position shown. FIGURE SOLUTION 250 mm Input link

Q: Relative analysis in two dimensions and dependent motion: If it is known that the instant shown in…

A: Motion of rigid bodies are not absolute or isolated and therefore it is described with respect to…

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A: Given: Angular acceleration = -5.9 × angle

Q: A belt moves between the pulleys of the crankshaft of the air conditioning fan and over the idler…

A:

Q: angular acceleration of the connecting rod is governed by the relationship α = -6.5θ where α is…

A:

Q: 1 Q2.The crane shown rotates at the constant rate w = 0.3 rad/s; simultaneously, the telescoping…

A:

Q: The acceleration of point A is defined by the relation a = -1.8 sin(kx), where a and x are expressed…

A: Given          a=-1.8sinkxk=3rads

Q: In a continuous printing process, paper is drawn into the presses at a constant speed v. Denoting by…

A: Given data as per the question The radius of paper roll = r The thickness of paper = b calculations

Q: The collar P slides outward at a constant relative speed u along rod AB, which rotates…

A: Given data  R = 250mm  Angular Velocity = 18rpm θ = 90° Need to determine the magnitude of…

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A:

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A: Given data:To find:Angular position when t = 3 sec.

Q: The motion of an oscillating flywheel is defined by the relation: 0 = 0,c7m/6 sin 4.zt, where 0 is…

A: Hence the angular position coordinates at t=0.125s, θ=0.253 rad  And at t=infinite θ=0radians

Q: A 3-in.-radius drum is rigidly attached to a 5-in.-radius drum as shown. One of the drums rolls…

A: a) The acceleration of point B is upward. Since the drums are rigidly attached, the linear…

Q: 2. Tid the percentage mercase in specu, in the Danis rise by 20 min. [Alls. 370] A Porter governor…

A: Ball 1 mass, m=3 kg Ball 2 mass, M=15 kg Arm length, BP=BD=200mm =0.2m Minimum radius of rotation,…

Q: At the instant shown in Fig. TT1.3, during deceleration, the velocity of an automobile is 13.3 m/s…

A:

Q: An airplane is moving due west at a speed of 100 mi/hr. The propeller blades is 5 ft. long (radius…

A: 100 mph = 146.667 f/s

Q: A Scotch yoke is a mechanism that transforms the circular motion of a crank into the reciprocating…

A:

Q: Gear A Radius = 0.06 m    Gear B Radius = 0.3 m       Gear C Radius = 0.36 m Note that the Load is…

A: From the given data,

Q: Both 15-cm-radius wheels rll without slipping on the horizontal surface. Knowing that the distance…

A: For wheel 1, Let the speed of wheel 1 be ω1Angular acceleration of wheel 1 be α1As wheel us pure…

Q: Question 1. A multi degree of freedom robotic arm moves so that P travels in a circle about Point B,…

A: Tangential acceleration, at=10 mm/s2 Speed, v=att   Normal acceleration, an=v2p=at2t2pwhere…

Q: The motion of an oscillating crank is defined by the relation u = u0 sin (π t/T) - (0.5u0) sin…

A:

Q: The motion of an oscillating flywheel is defined by the relation 0=00e-3πtcos 4, πt where 0 is…

A:

Q: A rocket sled is tested on a straight track that is built along a meridian. Knowing that the track…

A: Given data: The velocity of the rocket sled, v = 900 km/hr. Calculate the angular velocity of the…

Q: A homogeneous wire bent to form the figure shown is attached to a pin support at A. Knowing that r =…

A: Given Radius r = 220 mm Point B pushed down to 20 mm To find Magnitude of velocity B 8 s latter

Q: 1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and…

A:

Q: Pin A, which is attached to link AB, is constrained to move in the circular slot CD. Knowing that at…

A:

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A:

Q: disc rolls straight on a flat floor without slipping. The magnitude of the angular velocity ω= 3.0…

A:

Q: the angular velocity and angular acceleration of the idler pulley, (b) the total acceleration of the…

A:

Q: The mechanism shown in (Eigure 1) is used in a riveting machine. It consists of a driving piston A,…

A: Given:To find:Velocity of D.

Q: quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into…

A:

Q: A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is…

A:

Q: A helicopter moves vertically in the y direction at a speed of 10 km/h. Knowing that the main blades…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: A spring AB is attached to a support at A and to a collar (Figure 2). The un-stretched length of the…

A:

Q: 2. The horizontal rod OA rotates about a vertical shaft according to the relation 0 = 3t°, where 0…

A: Dear student,                    According to the guidelines I am allowed to answer only three…

Q: The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A,…

A: The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A,…

Q: A disc rolls without slipping. The magnitude of the angular velocity w= 1.0 rad/s, the angular…

A:

Q: For a certain range of motion the pin A is forced to move in the fixed slot parabolic by horizontal…

A:

Q: 1. At the state shown, the disk rotates about O in the counterclockwise direction at 4 rad/s. This…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: N=600 rpmt=4s

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: N=600 rpmt=4s

Q: Use translation and fixed-axis rotation

A: First, we need to calculate the distance travelled by cable C in 3 seconds. We can use the equation…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.