Load B is connected to a double pulley by one of the two inextensible cables shown. The motion of the pulley is controlled by cable C, which has a constant acceleration of 18 in/sec and an initial velocity of 24 in/sec, both directed to the right. Determine (a) the number revolution executed by the pulley in 3 sec, (b) the velocity and change in positions of the load B after 3 second. 3 In.o

Load B is connected to a double pulley by one of the two inextensible cables shown. The motion of the pulley is controlled by cable C, which has a constant acceleration of 18 in/sec and an initial velocity of 24 in/sec, both directed to the right. Determine (a) the number revolution executed by the pulley in 3 sec, (b) the velocity and change in positions of the load B after 3 second. 3 In.o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

18 40 29 10 Orthographic view. Note no hand drawing 47 (in catia v5) Clamp 26 Dia
What is relative position vector?
B.b. In a sentence, compare an average of the Capstone calculated angular velocity to your dsl calculation of change in angle divided by change in time. When might one be more useful than another?
Draw the diagram also,
a) An engine has a flywheel mass of 8-tonnes and a turning radius of 3 m. The energy fluctuation is 70 KN-m. The average speed of the engine is 160 rpm. Find the maximum speed value. b) A jet engine has a rotor with a weight of 500 N and this rotor rotates at 2400 rpm. Rotor It is suspended in the middle of the C and D bearings with a total distance of 600 mm between them and the center of gravity is rotated. 35 mm above its centre. By calculating the dynamic forces on the bearings, this system perform the balancing.
1. Where controlling the angularity of a feature of size, the feature control frame is associated with the 2. Orientation controls include and in some cases, 3. Where controlling the perpendicularity of a feature of size, the feature control frame is associated with the of the feature being controlled. of the feature being controlled.
What’s the correct answer for this please ?
What is a link precisely?
a) Figure Q3a shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 1300 revolutions per minute (rpm), calculate the angular velocity (w) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. [10 marks] Gear A: 44 Teeth Gear B: 96 Teeth Gear C: 60 Teeth Gear D: 140 Teeth Gear B- -Stage 2 Gear A- Input shaft- Stage 1- Gear C- -Gear D -Intermediate shaft -Output shaft Figure Q3a b) A motor with a power rating of 3600 Watts is coupled to the input shaft of the pinion (or driver) Gear A as shown in Figure Q3a. Calculate the torque at the input shaft and at the output shaft. Assume no losses and 100% efficiency. [5 marks] c) Draw a typical indicator diagram of pressure versus volume (p-v) to illustrate the actual Otto cycle for a four-stroke reciprocating internal combustion [RIC] engine. Clearly label each part of the p-v indicator diagram and clearly indicate when the piston…
Asap within 30 minutes
im sorry for the inconvinience , 500 d/d means 500 rpm. Its translated from turkish textbook , i forgot to translate the rpm value. Could you correct the substitutions please ?
Sketch the 2D figure using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 20 36 R 20R BR 36 BR 15 45 45 Upright | 2 holes 10 Dia 36K 158