Problem The composite bar system in Figure 4.8 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the rigid block. If the total applied load P=42000 lb, determine the stresses in the two bars. 2/2 Steel bar E₂ = 30 x 10 psi A₂ = 1in²

Problem The composite bar system in Figure 4.8 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the rigid block. If the total applied load P=42000 lb, determine the stresses in the two bars. 2/2 Steel bar E₂ = 30 x 10 psi A₂ = 1in²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the options
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
A composite beam is made of two brass [E = 120 GPa] bars bonded to two aluminum [E = 70 GPa] bars, as shown. The beam is subjected to a bending moment of 400 N-m acting about the z axis. Using a = 15 mm, b = 100 mm, c = 30 mm, and d = 65 mm, calculate (a) the maximum bending stress in the aluminum bars. (b) the maximum bending stress in the brass bars. Aluminum y Brass Aluminum b Brass C a d
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal
The composite bar in the figure is firmly attached to unyielding supports. Compute the stress steel (psi) caused by the application of the axial load P = 59 kips L1 = 16in; L2 = 10in
The composite bar is firmly attached to unyielding supports. The bar is stress-free at 50°F. Compute the stress in each material after the 80-kip force is applied and the temperature is increased to 100°F. Use a = 6.5 x106/°F for steel and a = 12.8 x106/°F for aluminum. Aluminum A = 2 in.² E = 10 x 106 psi 15 in. Steel A = 3 in.2 E = 29 × 106 psi 80 kips 10 in.
Read the question carefully and give me both right solutions with clear explanation. Don't copy from other websites solution
Given: Beam with loading and supports shown Maximum allowable stress in the steel bar is 30 ksi Determine: Maximum load P that can be supported Elongation of the bar Normal strain in the bar Shear stress in the " Ø bolt BAR K2 x5' 3' 34" BOLT IN SINGLE SHEAR RIGID BEAM Steel Properties E = 29,000 ksi (kips/in') G = 11,200 ksi Coefficient of thermal expansion = 6.5 x 10/ degree F