Problem Set – Temperature Change 2. Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers and tightened with nuts with an applied force of MN kN. Calculate the working stress of the rod and tube if the temperature during the fitting is 48 degrees Celsius. Modulus of Elasticity of Steel = 200 GPa Modulus of Elasticity of Copper = 100 Gpa Coefficient of Expansion due to Temperature of Steel = 12 x 10-6 / °C Coefficient of Expansion due to Temperature of Copper = 18 x 106 / °C Steel 20 mm o

Problem Set – Temperature Change 2. Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers and tightened with nuts with an applied force of MN kN. Calculate the working stress of the rod and tube if the temperature during the fitting is 48 degrees Celsius. Modulus of Elasticity of Steel = 200 GPa Modulus of Elasticity of Copper = 100 Gpa Coefficient of Expansion due to Temperature of Steel = 12 x 10-6 / °C Coefficient of Expansion due to Temperature of Copper = 18 x 106 / °C Steel 20 mm o

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
Problem Set – Temperature Change 1. A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is EN GPa. | 12 mm | 200 mm 900mm wide steel tire- 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire Fn- 100
The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter on the outside and 17 mm wire diameter. It measures 210 mm in free length. 82 Gpa is the modulus of rigidity. Calculate the initial compression length of the wire required to maintain a boiler pressure of 1.35 Mpa on a 30 mm diameter valve seat. (Draw the diagram)
A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod is made of SAE 4140 steel, compute the elongation due to a temperature change from -20°C to 140°C. TABLE3-4 Cocfficients of thermal expansion. a. for some
8.4 Please help ASAP. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Indicate your assumptions, write the given and make an organized solution.
PROBLEM:1 A gas engine valve spring is to have a mean diameter of 55 mm. The maximum load it will have to sustain is 584 N with a corresponding deflection of 7.18 mm. The spring is to be made of tempered wire. Since the material is to be subjected to repeated loading and fatigue must be considered a low working stress of 650 N/mm? will be used. Find the size for wire and number of coils used. Take modulus of rigidity as 0.84 x 105 N/mm? .Assume the spring coil is squared and ground. Take shear stress Concentration factor as 1.15.
This is a subject of Strength of MAterials, COmpute exactly without shortcut.Show FREE BODY DIAGRAM and COMPLETE SOLUTION thank you
pls find box ur answer Determine the value of the von Mises stress at point A. The von Mises stress at point A is This problem illustrates that the factor of safety for a machine element depends on the particular point selected for analysis. Here you are to compute factors of safety, based upon the distortion-energy theory, for stress elements at A and B of the member shown in the figure. This bar is made of AISI 1006 cold- drawn steel and is loaded by the forces F= 0.55 kN, P = 4 kN, and T = 25 N-m. Given: Sy= 280 MPa. 5 15-mm D. 100 mm- MPa.