Determine the net area of the given section below. Diameter of bolts is 7/8-in and the thickness of the plate is 3/8", in in2. The channel used is C8x15 and the plate in between the channels are 10" in width.   Select one: a. 6.69 b. 3.43 c. 2.25 d. 5.75

Q: A uniform block of steel (SG 5 7.85) will "float" at mercury-water interface as in the figure below.…

A: Given, SGB = 7.85 SGm = 13.56 SGw = 1

Q: Water at 10 Cflows from a large reservoir to a smaller one through a 5-cm diameter cast iron piping…

A: Given Diameter of the pipe = 5 cm = 0.05 m Flow rate = 6L/s Density = 999.7 kg/ms Friction…

Q: Problem 4. A cork ball (SG = 0.21) with a diameter of D = 0.30 m is tied to an object on the bottom…

A:

Q: Find the minimum diameter required of the circular steel shaft shown below if the largest shear…

A: Given, The length of the shaft is = 1.5 m Maximum allowable shear stress = 200 MPa Net torque is=…

Q: 1. Two blocks, of masses M = 2.3 kg and 2M are connected to a spring of spring constant k = 180 N/m…

A:

Q: An isentropic air compressor takes 150 m/min of air in at 10°C and 100kPa and compresses it to 1000…

A: Given: Flow rate (Q)=150m3/min Inlet temperature T1=10°C or 10+273=283K Inlet pressure P1=100kPa…

Q: The cross section of the rim of an iron flywheel 3 ft. In diameter is a rectangle 12" by 2". How…

A: A flywheel is a spinning device that is designed to efficiently store rotational energy by using…

Q: QUESTION 2: A particle is rotating in a circular orbit with radius r=5(A+5)m. The displace- ment…

A:

Q: 11. A diatomic gas (y 1'4) does 200 J of work when it is expanded isobarically. Find the heat given…

A: Data given -  Diatomic gas Y = 1.4  W = 200 J  Isobarically

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: Figure Q4 shows a rod of negligible mass whose ends has to particles A and B which slides along the…

A: Therefore the position of center of mass will be at distance of “3L/4” from the end “A” and at…

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is mm4 Select one: 540 x…

A: Dimensions of rectangle lamina b=60 mmd=30 mmIxx=112b×d3

Q: The process of reheating of the martensitic steel

A: Given; The process of reheating of the martensitic steel to reduce its brittleness without any…

Q: 2. The strings AB and AC connect the 200 g ball to the vertical shaft, as shown in Fig. 2. The shaft…

A:

Q: The main disadvantage of mechanical power systems is attributed to? O Complex construction O…

A: if we talk about any mechanical device, whether it is an small bicycle or a power plant, all the…

Q: Calculate the per meter (of length) pressure drop (units: kPa) associated frictional losses (only)…

A:

Q: Practice Problem 2.4.13: Calculate the moment of the force P about the axis AD using: 6 ft (a) point…

A: Given, P=240 lb The required coordinates x,y,z are, C(3 ft, 6 ft, 7 ft)E(0 ft, 8 ft, 0 ft)A(3 ft, 0…

Q: a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous…

A: Given b = 5.25 mm d = 12.75 mm To find Moment of Inertial X axis Y axis

Q: The moment of the force about point O *: is

A:

Q: A uniform square plate of mass m and side s, pivots about a horizontal axis through one of its…

A:

Q: 3.44 The landing gear of an airplane can be idealized as the spring-mass-damper system shown in Fig.…

A:

Q: %3D A rivet of 22 mm in diameter is used in the connection shown in Fig.8. If P = 80 kN, what…

A: given data;force(P)=80KN=80*103Nbearing stress(τ)=140MPadiameter of rivet(d)=22mmthickness(t)=?

Q: A dam on a river is built so that the wall facing the water is shaped like the region above the…

A: Given:The density of water is .The equation of curve is .The equation of line is .The water level is…

Q: team is generated at 4.0 MPa and 440°C and condensation ccurs at 0.15 MPa. (a) Considering that…

A:

Q: A rigid bar the fiqure . Cons fruct the the deg rees of freedom díffuse , Supporied by a massless…

A:

Q: For the composite area shown below, determine the moment of inertia about the horizontal centroidal…

A: Data given- I section  Base = 180 mm  Height = 160 mm

Q: In figure Shown, felocity at Section-1, is 1.7 and density of water slog is 1.94 Sa. Neglect losses,…

A: Data given - Velocity at section 1 = 1.7ft/s Density of water = 1.94 slug/ft3 To determine - h= ?

Q: A truck weighing 50kN is not moving on a hill which is inclined at 22 degrees to the horizontal.…

A:

Q: Please solve for 4.139  thx

A: Free body diagram of the problem To find The tension in the string Fdf

Q: Fluid Force. A swimming pool is filled with fresh water to a depth of 7 feet measured at the deep…

A:

Q: A cantilever beam of length 100-in carries three loads P1, P2 and 15 kip as shown. Choose distances…

A:

Q: Consider the truss shown in (Figure 1). Suppose that Fi = 4.5 kN and F = 6 kN. After the truss is…

A: Given dataForce F1 = 4.5kNForce F2 = 6kNTo determine the forces in the members BC HC and HG