Problem Set: Given is the partial floor plan of a certain building. a) Determine the load diagram of girder G-2 in gridline 5. b) Determine the allowable section with a ratio of d=2b of beam B-4 in gridline F/4-5 if the allowable bending stress is not to exceed 25 MPa. Assume the beam is adequately braced. (5) 5m 4m 15 kPa B-1 4m B-1 15 kPa 2.5m B-2 STAIRWELL B-2 5 kPa B-3 -5m 10 kPa B-3 G-1 G-2 10 kPa G-1 15 kPa B-4 -4m B-4 15 kPa B-1 B-1

Problem Set: Given is the partial floor plan of a certain building. a) Determine the load diagram of girder G-2 in gridline 5. b) Determine the allowable section with a ratio of d=2b of beam B-4 in gridline F/4-5 if the allowable bending stress is not to exceed 25 MPa. Assume the beam is adequately braced. (5) 5m 4m 15 kPa B-1 4m B-1 15 kPa 2.5m B-2 STAIRWELL B-2 5 kPa B-3 -5m 10 kPa B-3 G-1 G-2 10 kPa G-1 15 kPa B-4 -4m B-4 15 kPa B-1 B-1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ASAP PLEASE
Q1] A simply supported rectangular beam of 5m span carries characteristic pearmeant action(Excluding self weight of beam) of 10KN/m and variable action of 6KN/m respectively. The beam dimensions are breadth=250mm, effective depth=400mm. Assuming the following material strengths, Design the reinforcement . Fck=35N/mm², Fyk=500N/mm?.
0.9D+1.3W (When considering the wind load during construction) Calculation of required strength for axial force, shear force and bending moment of AB, BC, and DE members in 3 hinged frame Factored Load Application status
Q3: А- Oesign a rectangular beam with b = 350 mm, h = 625 mm as shown below. Use f! = 30 MPa, fy = 375 MPa and Ø18 mm for %3D fongitudinal reinforcement. Two lavers of tension reinforcement. PE45 kN Wu,-25 kN/m WUT14 kN/m D.L babulb 5 m B- Check the design of the singly reinforced beam shown below, if fc = 20 MPa and fy = 420 MPa, 030 mm for tension. Why? %3D sed edr arlagead iso t 430 mm 100 mm 300 mm
Show complete and clear solution.
a) A singly-reinforced concrete beam 300 mm wide and 650mm deep to the center of the tensile reinforcement is reinforced with 5 bars of 18 mm diameter. Find the ultimate moment capacity of the section. Take characteristic yield strength of steel as 415N/mm2.
a) Write and explain one advantage and onedisadvantage of using intermediate stiffeners in plate girders. b) If a plate girder design was initially determined to require intermediate stiffeners, but one optedtonot use them, how else could the plate girder be designed to achieve the same shaer capacity. c) A w-shepe beam is bent in bi-axial bending. All loading passes through its shear center. Please explain why the flexural strenght about its weak axis is the fullplastic moment capacity regardless of Lb
with fbd please
Design the shear reinforcement for the given beam below. Use fys = 275 MPa , fy = 415 MPa , fc' = 21 MPa b = 150 mm, d = 325 mm, ds = 10 mm dbt = 16mm , dbc = 12 mm. Column = 300 mm x 300 mm Calculate s in mm (answer should be divisible by 10)