Problem Number 3: Determine the maximum horizontal uniform load, w KN/m can the cable safely carry if the cable diameter is 105.5555 mm and has a strength of 500 MPa. What should be the estimated volume of the concrete at A (VA. m')if the unit weight of concrete is Yconcrete = 23.4987 KN/m²

Problem Number 3: Determine the maximum horizontal uniform load, w KN/m can the cable safely carry if the cable diameter is 105.5555 mm and has a strength of 500 MPa. What should be the estimated volume of the concrete at A (VA. m')if the unit weight of concrete is Yconcrete = 23.4987 KN/m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 250 Lample)For the beam sectiom shown afigrese, assume:- Pe= 28 MPa , fy= 420 MPa., EsIE =S 650 fr =…

A: Solution:- Neutral axis of section, b.x22=m×As×d-x250x22=8×1530×600-xx2+97.92-58752=0x=198.32 mm…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Answer To calculate the design Moment capacity of doubly reinforced beam for negative bending Moment…

Q: y 6-28 mm 75 mm 75 mm 350 mm

Q: An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of…

Q: 300 mm 2012 3014 250 mm Check the requirements of TS500 for ductile design and Determine the Moment…

A: Given: h = 300 mm b = 250 mm fc = 30 MPa fy = 420 Mpa d' = 25 mm

Q: D 25 mm deformed bars, it is required to: a.) Calculate and check the actual reinforcement ratio b.)…

A: Given : simply supported beam with udl and point loads acting 300 mm and 500 mm cross section 25 mm…

Q: Determine section shown in Fig. the nominal moment capacity of the Concrete strength and…

A: Given : f'c = 25 MPa and fy = 300 MPa Concrete cover = 50 mm This is a problem of RCC where we have…

Q: Using coefficients merthod (CF), Two-way supported slab panel No 3 in the figure below with the…

A: Two way slab Slab 3 is in case 1 i.e. interior panels We will have to find the moment coefficients…

Q: From the beam shown, fc' = 28 MPa, fy = 414 MPa, Bh = 1.20, Cc = 40 mm. Take D = 28 mm diameter…

Q: A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The…

Q: The shear forces acting on a beam are resisted by the stirrups together with the concrete. At the…

A: The expression to calculate Vc0 is given by, Vc0=0.6fctdbwd The value of the Design tensile strength…

Q: Determine the maximum live load that can be applied on one way slab shown in Fig. (1). The slab is…

A: One way slab Because of its geometry, the one-way slab is a slab that is supported by parallel walls…

Q: Compute the reaction at point A(kN) at member AD.

A: Given data; L.L = 2.949 kpa t = 112.110 mm w = 23.395 kN/m3

Q: Recitation 6 Design a one-way slab $3 having a simple span of 4m. The slab is to carry a uniform…

Q: A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. the…

A: Singly reinforced beams are those with longitudinal reinforcement only in their tension zone.…

Q: 3. A column shown below has tie reinforcement conforming to ACI 25.7.3. Assume normal- weight…

A: Given: concrte stress fc'=6000 psi allowed stress in concrete fc=60002=3000 psiand for steel grade…

Q: An RCC beam having 200 mm wide and 400 mm effective depth is reinforced with Fe415 grade steel of…

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

Q: Check the adequacy of a rectangular beam section with a width of 424 mm and an overall depth of 556…

A: To find Adequacy

Q: he slab is simply supported over a span of 7.5 m and carries a superimposed ccentricity of 40 mm.…

A: D.L = 3kpa L.L = 5kpa

Q: The wood pole is supported by two cables of % in. diameter. The turnbuckles in the cable are…

A: Diameter of the cable (dc) = 1/4 in. Permissible stress in cable (σc) = 60000 psi Permissible stress…

Q: Problem 1A 300×600 mm column is reinforced with 8 ∅ 22 bars 387 mm2 each, one in each corner as…

Q: 1. Total Compresive force acting on the beam 2. Ultimate Moment Capacity

A: Reinforced concrete has a high compressive strength contrasted with other structure materials.…

Q: Problem 4.39 Design the one-way slab shown in the accompanying figure to support a live load of 10…

A: A singly reinforced beam is a beam which is reinforced only in tension zone . The compression zone…

Q: A beam with a rectangular cross section of size 250 mm wide and 350 mm deep is prestressed by a…

Q: For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead…

Q: Determine the required reinforcement for T- section beam to resist torsion T = 11.75 KN.m with the…

A: Moment of resistance = 0.87 fy Ast [ d-0.42 xu] moment of resistance for high yield reinforcement =…

Q: A reinforced concrete beam has a width of 250 mm and a total depth of 450 mm. It is reinforced with…

A: Compression force generally happens when a physical force presses inward on a reinforced beam,…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

Q: T0.3 ine the maximum live load that can be applied on one way slab shown in Fig. (1). The slab is…

Q: A cantilever slab has a span of 2.40 m. It is 150 mm thick and has an effective depth d = 110 mm. It…

A: Given, span ,l=3 m service live load = 8.5 kPa service dead load = 1.5 kPa compressive strength of…

Q: PROBLEM 2 An actual allowable moment of 70 kN-m is carried by a beam with the cross-section shown.…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: for the slab shown below: 1- If the service dead load = 4 kN/m2, find the maximum live load can be…

A: As math type is not available, providing hand written solution

Q: ctangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and…

Q: QI) Slab system consist of two-way slab panels shown in Figure below, subjected to superimposed dead…

A: Given Dead load = 2KN/m2 beam dimensions, bw=350mm, h=750mm column dimensions 350×350mm, f'c=27MPa,…

Q: 7 1 التاريخ 2 الموضوع Q₁: The 300 mm X 300mm concrete columu. (EC 25 GPa and ac = 5.5 X 106 / "℃) is…

A: Given Data Size of column = 300mm × 300mm Diameter of reinforcement (d) = 18 mm × 4 no. Modulus of…

Q: 3. Which of the assumptions accepted when determining the ultimate moment resistance of reinforced…

A: The section 1 shown in the figure depict the prestressed concrete sections. Hence the assumptions…

Q: A beam with a rectangular cross section of size 250 mm wide and 350 mm deep is prestressed by a…

Q: Assume straight line instead of parabola for stress-strain curve of concrete as follows and partial…

A: Given- RCC sectionwidth b=300 mmeffective depth d=500 mm3 bars of grade Fe415dia=16 mM20 concrete…

Q: 1- For the floor system shown in Figure below, support service live load 4 KN/m? and service dead…

A: The given data is: fy=420 MPa f'c=28 MPa Load=2KN/m2 L.L=4 KN/m2

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Given, Width of beam=250 mm Depth of beam=500 mm Bottom bars =4-20 mm diameter Top bars=2-16 mm…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Problem Number 3: Determine the maximum horizontal uniform load, w
KN/m can the cable safely
carry if the cable diameter is 105.5555 mm and has a strength of 500 MPa. What should be the estimated volume of the
concrete at A (VA-
m')if the unit weight of concrete is Yconcrete = 23.4987 KN/m².
μ=0.3658, B= 35.8972°
↓
✓
TA
Details at B
60 m
120.00 m
15 m
20 m
30 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
A floor panel 3 4 m wide and 12 m long is intended for a vibratory machine in a factory. The concrete to be used has a strength of 27.6 MPa (whose density is 1800 kg per cubic meter) and reinforcement used has yield strength of 280 MPa Determine the minimum thickness of slab if the panel is cantilever
If the elastic sag of the concrete member was 3 cm for the corresponding continuous load, what is the final total sag in consideration of additional long-term sag due to creep and dry contraction? (However, the load loading period is 10 years, and the compression reinforcement ratio p′=0.005)
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
Based on Eurocode 2 (2004), the flexural capacity of the section shown below Is 60 kN.m for the concrete cylinder strength (fem) of 40 MPa. Estimate the flexural capacity of the section if the concrete cylinder strength (fcm) becomes 30 MPa. 150 mm Lever arm (z) = 180 mm
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
i need the answer quickly
using the table below, answer the question
A typical grade beam 300 x 800 is reinforced with 2 - 25M bars and the cover is forconerete cast and permanently exposed to the earth, (f', =30 MPa) Determine the following: (a) the size of the stress block "a" (b) the bending moment “M," (c) the c/d ratio (d) the type of failure (brittle or ductile) based on part (c) (e) check Asmin (equation 2.7) (Code 10.5.1.2) (f) maximum As permitted based on ductile failure (g) determine maximum bar size (2 required) from Table 1.5 based on part f) (h) check spacing requirements 's' Table 2.6 based on part g) (i) check if skin reinforcement is required Table 2.9 and fy = 400mpa please solve asap %3D
A singly reinforced rectangular beam 350 mm wide and 450 mm deep is reinforced with 2-16-mm-diameter bottom bars enclosed with 10-mm-dia stirrups covered with 40 mm of concrete.Calculate the tensile steel strain compatible with concrete strain of 0.003. Use f'c = 26 MPa and fy = 370MPa. Express your answer in 4 decimal places
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
Question 2: Determine the required reinforcement for L section beam to resist torsion T = 10KN.m with the following dimensions; depth of slab = 100 mm, width of flange = = = 200 mm, 900 mm, width of web depth = 455 mm. Consider concrete class C30 and high yield steel S460 for main Reinforcement and S250 For stirrups. 900mm = 1120 mm² -200mm