Problem H: For Problem Number 29 &30. Given the data below determine the required.k,= 10Scm/seck2= 3.0 x 103cm/seck3= 3.5 x 10 cm/secH,= 1.5 mH2= 2.5 mH3= 3.0 m29) Determine the ratio kH(eg)a) 7.545x102b) 7.597x103c) 7.621d) 7.62X10330) Determine the Kvleg).a) 2.597b) 2.789x106c)2.566x10sd) 2.959x105

Answered: Image /qna-images/answer/016bfb30-fb33-4437-bb1f-690ba1e44210.jpg

Problem H: For Problem Number 29 &30. Given the data below determine the required. k,= 10Scm/sec k3= 3.0 x 10°cm/sec k3= 3.5 x 10Scm/sec H,= 1.5 m H2= 2.5 m H3= 3.0 m 29) Determine the ratio kH(eq) a) 7.545x102 30) Determine the Kvleg). b) 7.597x103 c) 7.621 d) 7.62X103 a) 2.597 b) 2.789x106 c)2.566x10s d) 2.959x105

Problem H: For Problem Number 29 &30. Given the data below determine the required. k,= 10Scm/sec k3= 3.0 x 10°cm/sec k3= 3.5 x 10Scm/sec H,= 1.5 m H2= 2.5 m H3= 3.0 m 29) Determine the ratio kH(eq) a) 7.545x102 30) Determine the Kvleg). b) 7.597x103 c) 7.621 d) 7.62X103 a) 2.597 b) 2.789x106 c)2.566x10s d) 2.959x105

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. P Derive an equation that describes the vertical deflection of the beam, y(x), and also B calculate the maximum deflection of the beam. M = 0.5PL %3D
Answer and solve the following problem.
For the structure shown below, if E is .1 constant, what is the distribution ?factor at joint A (DFAB) 60 kN| 60 kN/m [90 kN (B I 21 I 3 m 4 m 4 m 2 m 2 m اخترأحد الخیارات a. 0.286 b. 0.5 c. 0.375 d. 0.625 e. 1 f. 0 O O
Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm2 , E1=E2= 100 GPa , a1=a2= 12x10/°C, AT= -25 °C, h= 1700 mm, 0 = 65° (1) (2) h B
P(kN)= 91
Determine the ybar in meters centroid of the figure shown. Where r2=9 m and r1=5 m
y=25kN/m P1=24kN P2=7kN
CLEAR SOLUTION ASAP
3. Determine and plot the Center of Gravity. Then Check whether the computed CG is correct. 17" 49" 30" 9" 11" C- 40 b D- 70 Ib E- 70 lb A- 201b B= 15lb Item Weight Arm Moment A B 2 3 D 4 E 5. ТОTAL Checking Item Weight Arm Moment 9. B. 10 11 D. 12 E 13 ТОTAL 69
Q2: 1.2 D.L x l.6 L.L Mu A: Find the maximum value of (p) that can be applied to the beam shown. Use f. =21.7 MPa and fy = 350 MPa (WD.L is included the self-weight of beam). %3D b hy P Wu =7 kN/m D.L 2028 A 500 mm 4028 250 mm -7.5 m-
STRUCTURAL ANALYSIS II
Consider W=1290KN/m