3. Determine and plot the Center of Gravity. Then Check whether the computed CG is correct. 17" 49" 30" 9" 11" B- 15lb C- 40 b D- 70 Ib E- 70 Ib A- 201b

Q: A 10 b weight is held abducted at the shoulder horizontal to the floo. The total length of the arm…

A: To determine the force that the deltoid is required to exert to hold the given weight.     Given,…

Q: Calculate for the moment of inertia for the beam shown below so that the maximum deflection will not…

A:

Q: The 100- Ib force of Figure below is the resultant of the couple and three forces ,two of which are…

A: Let Third force will be =F3

Q: Find: 1.) R in lbf 2.) Unit vector of R

A:

Q: 1) Locate the centroid of the cross-section and determine the moment of inertia of the section about…

A: Given values: Taking z = 5  Consider the cross section given:

Q: STA BM1 TP1 TP2 TP3 TP4 BM2 BS HI Determine the elevation of points by differential leveling with…

A: In Differential Levelling  Height of Instrument, HI = Elevation + BS ELEV = HI - FS. Where, BS is…

Q: A cantilevered beam AB carrying a uniform load, w as shown in Figure Q2 (c). The cross section of…

A:

Q: 3. Situation: You are driving when suddenly you saw a cat crossing across the street You applied the…

A: Given, Deacceleration of car, a = 8fps2 Distance covered, s= 456 ft final velocity of car, v=0

Q: SITUATION B: Prepare and complete the profile level notes for the information shown and perform the…

A:

Q: 2. 057 A. Convert the notes into a leveling notes of Rise and Fall and complete the data. B. Compute…

A: Formula  If IFS2  - BS1  is positive then rise If IFS2  - BS1  is negative then fall

Q: determine the moment of inertia along x and y axis with respect to the given axis and with respect…

A:

Q: (10) For a beam having the cross-section (dimensions in mm) shown in the figure below, which of the…

A: Given data:

Q: Q4/ Find the solution of following Differential Equation where the solution r the deflection…

A:

Q: 3x Jim (1-e y4 Xー0

A: solution  to find the limit of this problem  use the L- Hospital's rule  as the limit is in 0/0 form…

Q: or the beam in Figure below. a-Compute the immediate deflection due to total load. b-Estimate the…

A: Loading Diagram Section diagram Load (P) = 150 kN/mSpan of beam (L) = 5 mHeight of beam (h) = 660…

Q: DETERMINE THE FOLLOWING; A. CENTROID OF THE CROSS-SECTION B. SECOND MOMENT OF AREA OF THE STRONGER…

A: A Section of structure member is given belowNeed to find1- Centroid of the section2- second moment…

Q: 9. What will be the slope at point B? 10. What value of load P is needed in order to produce a zero…

A: Given P = 250 kNs = 2mW =-7x +81E = 200 GPaI = 2*109 mm4.It is asked to determine the following,1.…

Q: Using a W21X44 steel beam and A-50 steel, determine the value of P for the beam (use ASD and LRFD).…

A:

Q: Att = 0, a projectile is located at the origin and has a velocity of 20 m/s at 40° above the…

A: Given Data:Vo=20m/.sProjective equation y=0.4x-0.0036x2θ=40°To find a) X and Y co-ordinates, (in…

Q: y 5m- 750 N/m2 1217 N/m? -12 m - Fig. P3.54 -7.5 m- 12 m-

A:

Q: 2) Regd: Determine e of A relative to D Gst = 12 x 106 psi 101 lb ft 2-in. diameter 1000 lb · ft 900…

A:

Q: Which of the following equations is CORRECT? All symbols carry their usual means. v² 30(=+G) a) SSD…

A: Stopping sight distance (SSD) is the distance required for a driver to bring their vehicle to a stop…

Q: GOOmm Given a cantilever beam with given loadings and cross-section as shown in the figures, what is…

A: To Find :- first moment of area Q of the diamond cross section at the neutral axis.

Q: 31. What is the fixed end moment for CB? a. -15 k.ft. b. 15 k.ft. c. -10 k.ft. d. 10 k.ft, 32. What…

A:

Q: Calculate for the moment of inertia for the beam shown below so that the maximum deflection will not…

A:

Q: A (20°C) a rigid beam in placed upon the rods shown in figure: Determine the magnitude of uniformly…

A: Finding out the value of W.

Q: Calculate for the moment of inertia for the beam shown below so that the maximum deflection will not…

A: Given, Span Of the beam = 12m We need to Calculate Momen of intertia (I) value using moment area…

Q: A cross-sectional area of 322.58 mm of an aluminum bar which carries the axial loads applied at the…

A: Find the total change in length of the bar

Q: Ex's For the beam shown below, Find (Wii), use fo`=21/pa. EYE 400 Mpa.... Wu 5m. 100m 100m 100mm…

A: Given: b = 200 mm d = 350 mm span = 5 m fc = 21 MPa fy = 400 MPa

Q: Example Problem 3: Determine the value of P just sufficient to start the 10° wedge under the 400lb…

A:

Q: a a 100 mm -75 mm- - 75 mm- 50 mm 100 mm 50 mm A a Figure Q2[b]

A:

Q: Given the following: b=360mm d=550mm fc'=35MPA fy=420MPA Mu=700KN-m Determine As LISE N SCR 2015 As…

A:

Q: Question 1 * Each member of the truss shown is made of steel and has the cross-sectional area shown.…

A:

Q: (1 - ++ e) (Gs+ Se) Xu A I te WHY OR HOW DID THIS BECOMES 1 (Gs + Se) Xw

A:

Q: W1 W2 Florescence No. Load(KN) (DRY WEIGHT) (WET WEIGHT) 2500 area (mm) 1 518.4 2100 600 520.1 2120…

A: Consider the table data given in table; No. Load (kN) W1 (Dry weight) W2 (wet weight) Florescence…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.