Problem A spiral column 600 mm in diameter has an unsupported height of 2.4 m. The column is bent in single curvature and is braced against side sway. Steel ratio is at 1.70%. Given: Axial loads at service condition Dead Load, DL = 3,208 KN Live load, LL 1,438 KN = Compressive strength, fc' = 27.5 MPa Steel yield strength, fy = 413 MPa Find the number of 32 mm diameter bars considering ultimate design load condition. (round up to the next whole number)

Problem A spiral column 600 mm in diameter has an unsupported height of 2.4 m. The column is bent in single curvature and is braced against side sway. Steel ratio is at 1.70%. Given: Axial loads at service condition Dead Load, DL = 3,208 KN Live load, LL 1,438 KN = Compressive strength, fc' = 27.5 MPa Steel yield strength, fy = 413 MPa Find the number of 32 mm diameter bars considering ultimate design load condition. (round up to the next whole number)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

need answer thank you
Hello help me answer this. Thank you.
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
please include also the given, required and the solution thank you
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section.
Show complete solution. Thank you