Problem A 300 mm x 600 mm reinforced concrete beam section is reinforced with 4 -28-mm- diameter tension steel at d = 536 mm and 2 - 28-mm-diameter compression steel at d' = 64 mm. The section is subjected to a bending moment of 150 kN-m. Use n = 9. 1. Find the maximum stress in concrete. 2. Determine the stress in the compression steel. 3. Calculate the stress in the tension steel.

Problem A 300 mm x 600 mm reinforced concrete beam section is reinforced with 4 -28-mm- diameter tension steel at d = 536 mm and 2 - 28-mm-diameter compression steel at d' = 64 mm. The section is subjected to a bending moment of 150 kN-m. Use n = 9. 1. Find the maximum stress in concrete. 2. Determine the stress in the compression steel. 3. Calculate the stress in the tension steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
Solution w/FBD
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
Give me right solution according to the question.. where Y = 146 X1 = 102.2 X3= 146 X= 551 X2= 363.66
A prestressed concrete beam of rectangular section 300mm wide and 600mm deep is prestressed by 5 pieces of 8mm high tensile wires at 500mm from the top and 15 pieces of 8mm diameter high tensile wires at 83 mm from the bottom. The initial stress in the wires is 1200 MPa. Estimate the loss of stress in the bottom wires due to elastic shortening of concrete. Assume modular ratio = 6.