Problem 7.33 Consider the motor mounted on a cantilever beam in figure shown below. The motor has a massof 8 kg and runs at the constant speed of 3500 rpm. The steel beam is 15 cm long, 10 cm wide, and 1 cm thick.The unbalanced part of the motor has a mass of 4 kg and an eccentricity of 0.3 mm. The damping in the beamis very slight. Design a vibration absorber for this system. The available clearance for this system. The availableclearance for the absorber's motion is 2.5 cm. The modulus of elasticity of steel is approximately E2 x 1011 N/m²=Motor12Beam(a)me(b)сx

Answered: Image /qna-images/answer/eb74df70-cd43-435b-9419-73302df694d7.jpg

Answered: Problem 7.33 Consider the motor mounted…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

need it correctly
A metal polishing machine consists of a box full of ceramic particles mounted on the top of a shaker device as shown in the figure below. The shaker runs at f = 24.2078 Hz and carries an out of balance mass of mo = 19.9725 kg at a distance of e = 0.0499 m from the centre. The static deflection of the spring is A = 19.3179 mm, the damping constant is c= 20239.4652 kg/s and the total mass of the machine is M = 813.8726 kg. Assume that gravitational acceleration is g = 9.81 m/s?. The amplitude of the steady state response of the system is:
Hi, please answer this question. Thank you very much
As illustrated in the figure below, the bedplate of an experimental diesel engine is supported on four springs to isolate the vibrations from the test frame. The effective weight of the diesel engine and bedplate is 43kg and the stiffness of each of the four springs is 250 kN/m. Using a simplified approach - by applying Newton's Second Law assuming a single degree of freedom system and ignoring damping - what rotational engine speed is best avoided? Bedplate Test engine Supporting springs Figure: Sketch of a test engine mounting arrangement Give your answer in rad/s to 1 decimal place.
A motor rotates at 750 rev/min and has a moment of inertia of 0.15 kgm2. It drives a load through a gearbox at 250 rev/min with a moment of inertia of 0.25 kgm2. The torque on the load shaft varies sinusoidally with an amplitude of 180 Nm. The speed of the load is to be regulated to ± 4% of the mean by adding a flywheel to the motor shaft. Calculate this moment of inertia to be added and the mass of the flywheel that is a plain disc of radius of 400 mm.
ENGINEERING VIBRATION QUESTION.An electric fan with a mass of 50 kg is subjected to harmonic excitation due to an unbalanced mass. A spring-damper system was designed to minimize the force transmitted to the bottom of the fan. An attenuator with an attenuation ratio of ζ = 0.2 was used. Calculate the spring stiffness so that the force transmitted to the floor is less than 10% when the fan rotates at 10,000 rpm.how can i solve it..... It's too difficult for me. 6
A machine of 250 kg mass is supported on springs of total stiffness 100 kN/m. Machine has an unbalanced rotating force of 350 N at speed of 3600 rpm. Assuming a damping factor of 0.15, the value of transmissibility ratio is:
Explain the Schematic Diagram in this problem. (tanginamo1 is the problem) and (tanginamo2 is the schematic diagram) Provide a reasonable explanation, thank you!
A belt pulley is designed as a flywheel. it has a moment of inertia of 100kgm^2 and is supposed to be accelerated from a resting position to a rotational frequency of 600 min^-1 within 15 seconds. you have to calculate the acceleration torque without considering the friction of the bearing
The maximum permissible recoil distance of a gun is specified as 0.5 m. If the initial recoil velocity is to be between 8 m/s and 10 m/s, find the mass of the gun and the spring stiffness of the recoil mechanism. Assume that a critically damped dashpot is used in the recoil mechanism and the mass of the gun has to be at least 500 kg.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS