PROBLEM 7.20Two members of uniform cross section 50 x 80 mm are glued together alongplane a-a that forms an angle of 25° with the horizontal. Knowing that the allowable25"stresses for the glued joint are o = 800 kPa and 7 = 600 kPa, determine the largestcentric load P that can be applied.50 mmP = 3.90 kN

Any action that can change the state of motion is called force. Force is described by its magnitude,…

PROBLEM 7.20 Two members of uniform cross section 50x 80 mm are glued together along plane a-a that forms an angle of 25° with the horizontal. Knowing that the allowable stresses for the glued joint are o = 800 kPa and 7 = 600 kPa, determine the largest centric load P that can be applied. 50 mm -

PROBLEM 7.20 Two members of uniform cross section 50x 80 mm are glued together along plane a-a that forms an angle of 25° with the horizontal. Knowing that the allowable stresses for the glued joint are o = 800 kPa and 7 = 600 kPa, determine the largest centric load P that can be applied. 50 mm -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 8.12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is bent in the shape of a horse shoe having a mean radius of 70 mm. Two equal and opposite forces of 10 kN each are applied at a distance of 12 cm from the centre line of the middle section so that they tend to straighten the rod. Find the maximum ten- sile and compressive stresses and construct a diagram showing the vari- ation of the normal stresses over the central section.
Problem 5 Rigid member ABC is supported with two links BE and CD which have a cross section area of 230 and 300 mm? respectively. Determine the maximum applied force Q knowing that the maximum movement of point E is 0.45 mm. D Brass E - 105 GPa 230 mm B C E Aluminum E = 70 GPa 150 mm 65 mm 230 mm Area given is for member AB not BE Cross section area of links AB and CD are 230 and 300 mm^2 respectively.
PROBLEM NO. 2 For the frame shown, a 4998-N load is acting on member ABD at D. If the allowable material shear stress for is 49 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C. 4998-N 1.00 m 1.59 m 45° 0 O B A 1.59 m 1.58 m
Solution?
Question 3. A 4 by 4-in. wood-post BC is connected to a 1-in. diameter steel eye-bar AB to form a hoist. A load of w = 7000 Ibs is applied at point B on the hoist. (a)Determine the axial stresses in members AB and BC. (b) Determine the cross shearing stress in the 1-in. diameter bolt at point A. STEEL V -7000 lb WOOD FIG. I A
An annular washer distributes the load P applied to a steel rod to a timber support. The rod's diameter is 22 mm, and the washer's inner diameter is 25 mm, which is larger than the hole's permissible outer diameter. Knowing that the axial normal stress in the steel rod is 35 MPa and the average bearing stress between the washer and the timber must not exceed 5 MPa, examine the smallest allowed outer diameter, d, of the washer. %3D %3D +22 mm P Figure 4
1.6 (A). An 1-seetion girder is constructed from two 80 mm x 12 mm flanges joined by an 80 mm x 12 mm web. Four such girders are mounted vertically one at each corner of a horizontal platform which the girders support. The platform is 4 m above ground level and weighs 10 kN. Assuming that each girder supports an equal share of the load, determine the maximum compressive stress set up in the material of each girder when the platform supports an additional load of 15 kN. The weight of the girders may not be neglected. The density of the cast iron from which the girders are constructed is 7470 kg/m³. [2.46 MN/m²]
5. Three wood boards, each 3.5 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood are 750 psi in tension and 1450 psi in bearing, find the largest allowable value of the force P. ² 1 in. P 2 in. P 1 in. T in.
Que 5.6. A crane hook trapezoidal horizontal cross-section is 50 mm wide inside and 30 mm wide outside. Thickness of the section is 60 mm. The crane hook carries a vertical load of 20 kN whose line of action is 50 mm from the inside edge of the section. The center of curvature is 60 mm from the inside edge. Determine the maximum tensile and compressive stresses in the section.
PROBLEM 1.2 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d = 50 mm and dz = 30 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC. 300 mm 40 kN 250 mm V30 KN