1.0 mm, E = 142 GPa,ut each lamina made of Carbon/Epoxy, lamina thickness t =E2 = 10.3 GPa, G12the calculations.0.27, V230.38. Use Newton, mm, and MPa for7.2 GPa, vị2 =Jaminate with each

GivenMatrics for a one-lamina 30 G12=7.2Gpat=1.0mmE1=142GpaE2=10.3Gpaν12=0.27ν23=0.38

Problem 6.11 Compute the [A], [B], and [D] matrices for a one-lamina [30] laminate 142 GPa, with each lamina made of Carbon/Epoxy, lamina thickness t = 1.0 mm, E1 : E2 = 10.3 GPa, G12 0.38. Use Newton, mm, and MPa for %3D 7.2 GPa, v12 = 0.27, v23 = || the calculations, vith each

Problem 6.11 Compute the [A], [B], and [D] matrices for a one-lamina [30] laminate 142 GPa, with each lamina made of Carbon/Epoxy, lamina thickness t = 1.0 mm, E1 : E2 = 10.3 GPa, G12 0.38. Use Newton, mm, and MPa for %3D 7.2 GPa, v12 = 0.27, v23 = || the calculations, vith each

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

One end of a wire is attached to the ceiling. It has an elastic limit of 200 x 10^6 Pa. If it has a radius of 3.45mm, what is the maximum load (in kilograms) that can be hung on the other end before it breaks? (g = 9.8m/s^2) (round your answer to nearest whole number)
A disk of SBR elastomer 3.0 cm in diameter 0.5 cmthick is used as a cushioning surface between two steel rods ofthe same diameter, as shown below (not to scale). a. If the rods are brought together with an axial force of 100 N such that the SBR is compressed elastically between them, what is the thickness of the SBR under load? b. Under the same conditions as part (a), what is the greatest possible diameter of the SBR under load? c. If the SBR is bonded to the rods, how far can one rod be rotated with respect to the other before the SBR/rod interface fractures? Assume that the rods are essentially rigid and the distance between them remains constant. Please answer in degrees of rotation.
To support a tensile load of 65 kN, a metallic rod with a circular cross section and a length of 0.32 m will be used. It is desirable that the tension in the bar should not exceed 240 MPa and the maximum elongation should be 0.42 mm. What is the minimum rod diameter [m] in these conditions? Calculate. (For a metallic bar, take the elastic modulus as 220 GPa).
1. A 0.5-m long solid shaft of a rice thresher is stressed at 100 MPa during operation. If the torsional deflection is 2 degrees, compute the shaft diameter. What power is transmitted by the shaft at 20 Hz? Use G= 83 GPa. %3D
:>> Develop the lateral surface of a hexagonal prism of base edge 20mm and axis height of 50mm restingon its base on HP such that its one base edge is parallel to VP.
If Eg = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a volume by 0.6 percent?
A rectangular polypropylene [E = 6.200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400 MPa] bar (2) at flange B. The assembly (shown in the figure) is connected to rigid supports at A and C. Bar (1) has a cross-sectional area of A₁ = 920 mm² and a length of L₁ = 1220 mm. Bar (2) has a cross-sectional area of A₂ = 2630 mm² and a length of L₂ = 570 mm. After two loads of P = 3.8 kN are applied to flange B, determine: (a) the forces in bars (1) and (2). (b) the deflection of flange B. (a) F₁ = F₂ = (b) UB = i i i A kN KN mm L₁ (1) P B L₂ (2)
5. A bone containing a solid polymer filler acting as an implant is tested by the application of a 2000N force to its midpoint. Assume the polymer is perfectly bonded to the bone. In the central region of the bone, the cross- section is approximately circular. For the cortical bone, E₂ = 20 GPa For the polymer, Ep = 1.8 GPa (a) Determine the location of the maximum bending moment in the system. .2m (b) Calculate the maximum bending stresses in the bone and in the polymer at the interface point H. 7.03 Mpa 78.13 Mpq along length For a circle, I = r²/4 from left relative to centroid end veslect small angle here P To = 12 mm 40 cm Bone, B |r₁ = 6 mm Solid Polymer fille Polymer, P
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E - 29,000 ksi; a - 6.5x10-6/°F] bolts have a diameter of 0.45 in. The polymer [E - 370 ksi; a - 39.9x 10-6/°F] cylinder has an outside diameter of 6.2 in. and awall thickness of 0.35 in. Assume a - 27 in. and b - 35 in. If the temperature of this assembly changes by AT - 145°F, determine: (2) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. (1) (2) (1) Answer: (a) 02 - psi. (b) E2 - (c) E1 - με
14. A bar of 2 m length, 20 mm breadth and 15 mm thickness is subjected to a tensile load of 30 kN. Find the final volume of the bar, if the Poisson's ratio is 0.25 and Young's modulus is 200 GN/m?. [Ans. 600 150 mm³]
To support a tensile load of 65 kN, a metallic rod with a cross-sectional area of Circle and a length of 0.32 m will be used. It is desirable that the voltage on the rod does not exceed 240 MPa, and the maximum extension is 0.42 mm. How many [m] should the minimum (minimum) Rod diameter be in these conditions? Calculate. (Take the elasticity module as 220 GPa for the metallic Rod).
The Cable in figure P1.2 has a diameter of 1/5 in. If the maximum stress in the cable must be limited to 4 ksi(T), what is the maximum weight that can be lifted? (FBD need)