Problem (5.2) An impulse turbine has a number of pressure stages (pressure compounded turbine). The nozzle angle in the first stage is 20° and the blade exit angle 30°. The blade speed =120 m/s and the velocity of steam leaving nozzle =300 m/s. If the blade velocity coefficient =0.8 and the nozzle efficiency 0.85, find the work done per kg steam and the stage efficiency. If the steam supplied to the first stage is at 2 MPa and 250°C and the condenser pressure =0.01 MPa estimate the number of stages required.

Problem (5.2) An impulse turbine has a number of pressure stages (pressure compounded turbine). The nozzle angle in the first stage is 20° and the blade exit angle 30°. The blade speed =120 m/s and the velocity of steam leaving nozzle =300 m/s. If the blade velocity coefficient =0.8 and the nozzle efficiency 0.85, find the work done per kg steam and the stage efficiency. If the steam supplied to the first stage is at 2 MPa and 250°C and the condenser pressure =0.01 MPa estimate the number of stages required.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. For Francis turbine with the following specifications: Pdev= 225 MW, H=250 m , nov= 90 % , If the velocity of water at spiral case entering =24 m/s, and the volumetric efficiency is 0.98, thus the diameter of the spiral case entering is: а. 2.3 m. b. 2.8 m. с. 3.1 m. d. 3.6 m. e. None of them.
4.1 A gas turbine power plant is operating as follows. Compressor intake air temperature T, is 306 K, pressure p, is 100 kPa, and compressor pressure ratio B is 15. TIT T, is 1490 K. Isentropic efficiency of compressor N, is 0.88, and that of turbine n is 0.91. Air mass flow rate mi, is 636 kg/s. Fuel mass may be ignored. Calculate (i) actual temperatures at compressor and turbine exits, (ii) plant actual net specific work per kg air, (iii) plant actual power output, (iv) plant actual rates of heat addition and rejection, and (v) plant actual thermal efficiency.
Q. The velocity of steam leaving a nozzle of Turbine is 896 m/s and the nozzle angle is 20°. The blade velocity is 300 m/s and the blade coefficient is 0.79. Assuming the mass flow rate as 1 kg/s and the runner blades are symmetric. Determine the power developed in kW
A Pelton wheel develops 70 kW under a head of 60 m of water. It rotates 400 rpm. Overall efficiency is 80%. Find the discharge rate in m³/s. Use the equation below, where P is power of the turbine shaft and no is the overall efficiency, where specific weight of water is is 9.80 kN/m³ no P YQH A generator is driven by a small, single-jet Pelton turbine designed to have a power specific speed sp 0.20. The effective head at nozzle inlet is 200 m and the nozzle velocity coefficient is 0.985. The runner rotates at 880 rev/min, The turbine overall efficiency is 80%. Find (a) the power delivered by the shaft of the turbine and (b) find the power delivered by the water to the turbine. where density of water is 1000 kg/m³ and g is 9.80 m/s². Use Stup Ω P/p (gHE)* Overall efficiency ne and Power developed at turbine shaft hydraulic power P YQH
Q - The rotor of an impulse turbine is 60 cm diameter and runs at 9,600 r.p.m. The nozzles are at 20° to the plane of the wheel, and the steam leaves them at 600 m/sec. The blades outlet angle are 30° and the friction factor is 0.8. Calculate the power developed per kg of steam per second and the diagram efficiency.
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
Identify what is the system in this problem and write the general energy balance equation (no need to solve) A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the specific delta H?
A single stage single acting reciprocating air compressor has 0.25 m x 1.75 m runs in 750 rpm is to deliver 0.20m³ free air per second from 101.3 kPa to 355 kPa. Calculate (a) the volume displacement (b) the volumetric efficiency (c) the isothermal work done, compression is at pV =c (d) the isothermal compressor efficiency if the the indicated power of compressor is 40kW
Problem (5.1) An impulse turbine is supplied with steam at a pressure of 1.6 MPa and temperature of 250°C. The back pressure is 0.012 MPa. Nozzle efficiency is 0.9. Blade velocity coefficient K=0.8, mechanical efficiency=0.9, nozzle angle =20°. Symmetrical blades with angle 30°. Find the revolution per minute if the mean diameter of wheel is 75 cm, the blade efficiency, axial thrust per kg steam, exit loss and the stage efficiency.
Problem 3: Water is fed to an inward flow reaction turbine, running at 180 rpm with a velocity of flow of 3 m/s. The diameter and width of the wheel at inlet are I m and 135 mm, respectively. Assuming the velocity of flow to be constant and radial discharge at inlet and outlet, find, (a) work done per kN of water, (b) power developed by the turbine,