Problem 4. A. Draw the F.B.D. of the frame B.Draw the F.B.D. of the figure shown in (4-B), if the cylinder is in equilibrium, determine all the forces affect it. 5 lb/ft 1.50 ft. 4.00 ft 2.00 ft 3.00 ft Fig (4-A) 3.00 ft 3 lb/ft cable W=100 lb 30 All surfaces are smooth Fig (4-B)

Problem 4. A. Draw the F.B.D. of the frame B.Draw the F.B.D. of the figure shown in (4-B), if the cylinder is in equilibrium, determine all the forces affect it. 5 lb/ft 1.50 ft. 4.00 ft 2.00 ft 3.00 ft Fig (4-A) 3.00 ft 3 lb/ft cable W=100 lb 30 All surfaces are smooth Fig (4-B)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia IG=10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the work or U1->2 (in ft-Ib) after it has moved 4.2 ft downward
Show complete solution. Thank you
The ABC rigid bar is suspended by the BD rigid bar and by an A pin that connects it to the other ADE rigid bar. If the overhang load at point C is equal to 12kN, calculate the force on the BD bar and the reactions FA = √??2 + ??2, on pin A and the reaction FE roller located at point E. Disregard the weights of all the bars.
The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab. Sketch the loading that acts along the joist BF and side girder ABCDE. Set a = 10 ft, b = 30 ft. What is the reaction at point F in kips?
Q-2: Through a very narrow gap of height 'h', a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity m,and on other side oil of viscosity m². Calculate the position of plate so that : (i) The shear force on two sides of plate is equal.
The tube supports the four parallel forces. Determine the magnitudes of forces FC and FD acting at C and D so that the equivalent resultant force of the force system acts through the midpoint O of the tube.
1. Write about the effects of the Stability and Determinaey of Engineering Structures on the economical of the structures in design. 2. For the structural beam shown; noting that the internal hinges lies in the midspan of the beams; find the following: a. Draw the shear and bending moment diagrams. b. Construct Influence Lines for : (Rc, Rr. Sp, Sright-E, Sten-E, Mc, Stet-F) 6.9 W A B
EX: Draw moment diagram of rigid frame structure. EI-constant 8KN/m B i 4]D E 4m A C 4m 4m |-
Determine the moments in the beam at A, B. and C. O-15 1. What is MAB in kN-m? 15 Select the correct response: 30 12 kN/m -30 5m
Q.1) For the frame shown in figure have a two- member (ABOC and EDC) and is pin connected at E, C and A. If a 750 N force is applied directed vertically (a) at B, (b) at D. Determine the horizontal and vertical components of reactions at pin E and A. 50 mm 170mm 125 mm C 75 WE
1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is perpendicular to the member AB, determine the tension on the rope and the horizontal and vertical components of forces at B. Assume roller connection at A. 2000 N 2 m Fim--1 m- 1500 N 2 m 2 m 45° A
Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the support at B fails at any moment greater than 18 kN-m. Then support B is (a) Unsafe (c) Just Safe A L, EI D L, EI D 80 kNm B L, EI L, EI C (b) Safe (d) Cannot be determined