Problem 3. * PROBLEM 3: Block A weighs 280. N and block B weighs 500. N. Block A is held by a cord fastened to the wall. Force P is applied on B to drag it to the left at constant speed. The coefficient of friction between A and B is 0.30 and that between B and the floor is 0.32. Find the following (a) the normal force exerted by B on A, NA. (b) the tension in the cord attached to A, T (c) the frictional force exerted by B on A, f, (d) the force applied on B, P (e) the frictional force exerted by the ground on B, fa- 60° A 20° B

Q: Help!!! Please answer all Correctly!!! Please

A: Step 1:Step 2:Step 3:Step 4:

Q: Using the general Lagrange equation, write the model for the elevator shown. Sketch the block…

A:

Q: ecieved an answer to this question before, but I don't understand it. We're supposed to use vectors…

A: β=tan-13+OC.COSθ7-OC.SINθ  =tan-13+4.2×COSθ7-4.2×SINθl=2×2.8×SINθ2 =5.6 SINθ2

Q: 4. Description: Suppose the flanged train wheel at the right is 0.6 in in radius with an additional…

A: Inner radius of wheel→ri=0.6 in Outer radius of wheel→ri=0.6+0.4=1 in

Q: Help!!! Please answer Correctly !! Clearly solved Please !!!!!!!!

A: Step 1Step 2Step 3 : Step 4

Q: 1. The diagram below shows the generalised model of the fixed wheel as covered in the course: Robat…

A: Solution: Given Data: l=3 α=3π4β=π4r=4

Q: Q/1-B: For the solid geometry shown in figure below, construct the required CSG tree.

A: Find Construct the required CGS tree.

Q: You are a structural Engineer who works in Dar Al Handasah company. Your manager has called for a…

A: As the question is having more than three sub parts, first three are solved.

Q: Determine mass m, in pulley system shown in Figure -1. Also determine forces in points A & B. mass…

A:

Q: Please break down every step so I can understand the complete concept of how to algebraically work…

A: I have provided the clear explanation in the below images. If you need any further assistance please…

Q: A3.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Step 1:Step 2: Step 3: Step 4:

Q: Find the member force in AB. 2. Find the member force in BC. 3. Find the member force in BD. 4.…

A:

Q: Each figure shows a mechanical device in which one or more forces are applied parallel to and away…

A: Given: Force acting at 150 mm above the axis of the horizontal beam: →F=800 N Because there is one…

Q: Question 4: T shape homogeneous bar m=50 kg mass. Compute the reaction at the pin O just after the…

A: Mass of the T-shape homogeneous bar,

Q: 2) As the foot contacts the ground, a ground reaction force of 200 Nat 55* relative to the…

A:

Q: Don't use chatgpt. I need a handwritten solution

A: Step 1:Given:Vertical post length: H=7m T1​=6N T2​=8N θ=35∘Unknown:The expected reaction moment at…

Q: The Reactions are Given. Draw the Shear and Moment Diagrams and deflection diagram

A: Consider a section at a distance of x from the left end of the beam. For a section AB of the beam,…

Q: Statics and Equilibrium Draw and label a complete FBD of each beam Solve for the reaction forces…

A:

Q: Question 1 A propped cantilever beam is loaded by a bending moment of the magnitude MB at the point…

A:

Q: 1. You are tasked to design a shaft for power transmission through a belt and pully at its right…

A: Given:To find:

Q: Chapter 2 Problems 214 Abox weighing 25 pounds (assumed concentrated at ils center of gravity) is…

A: Given: To calculate the moment about Point A. W=25 lb F=20 lb

Q: For the beam shown, (1) derive equations for the shear force V and the bending moment M for any…

A: Consider horizontal forward & vertically upward force as (+)ve and CW moment as (+)ve & CCW…

Q: 2. Find the reaction at the support for the following Figure 2. 480 lb/ft 600 lb/ft A D B C -3 ft- +…

A: Where,P = Equivalent load due to a uniformly distributed load from C to Dx = Distance of load P from…

Q: Q3 (Gyroscopes) The essential structure of a certain type of aircraft turn indicator is shown in the…

A: Given: The spring stiffness, K = 500 N/m The mass of uniform disk, m = 200 g = 0.2 kg The radius of…

Q: Determine the bending moment acting at each of the following locations: (a) x = 5.8 ft (i.e., at…

A: Given DataP=1200lba=5.8ftw=215lb/ftMD=6700lb.ft Here the Free Body diagram

Q: once answered Correctly will UPVOTE

A: Solution:- Given data:- γ =93 ln/ft3 let, moment of inertia about center of gravity G IG =…

Q: 3-17 A pair of ice tongs is shown in Figure P3-7. The ice weighs 50 lb and is 10 in wide across the…

A:

Q: A guy who works out at your gym found out that you are an engineer and has hired you do an analysis…

A: Data given-

Q: An object of mass 4 grams hanging at the bottom of a spring with a spring constant 5 grams per…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.