Problem 3: For the weightless truss shown, calculate the vertical displacement of point c under the following d EA = 25,000 k conditions: 4 ft (a) due to the 10-kip point load at point c; (b) due to member ab being fabricated 0.15 inch short; (c) 1.0 inch vertical settlement of point b. You may assume that all members are braced against instability. Provide answers for each of (a), (b), and (c) assuming they occur independently. a 10 kips 20 ft 4 ft -

Problem 3: For the weightless truss shown, calculate the vertical displacement of point c under the following d EA = 25,000 k conditions: 4 ft (a) due to the 10-kip point load at point c; (b) due to member ab being fabricated 0.15 inch short; (c) 1.0 inch vertical settlement of point b. You may assume that all members are braced against instability. Provide answers for each of (a), (b), and (c) assuming they occur independently. a 10 kips 20 ft 4 ft -

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

WRONG ANSWERS GETS DOWNVOTE
Q\ Analysis the truss below. P= 3 kn P=3 kn P 20 KN Figure 1 D E 6.67 m 6.67 m 6.86 m 6,86 m 6.86 m 6,86 m 6.86 m 6,86 m B 6.67 m 6.67 m 6.67 m
Draw the shear and bending moment diagram of the given system. Flexural rigidity is equal to El. Use Method of consistent deformation. 20 kN/m 60 kN A 12 m 4 m
Completely solve and box the final answers.
Current Attempt in Progress Determine the force in member AE of the loaded truss. The force is positive if in tension, negative if in compression. A kN 3.0 m 2.8 m F Answer: AE = i 3.1 kN B E 3.0 m 4.8 KN 1.4 m D
Q2 For the truss shown in the figure:: 4. Determine the force in member fe using the joint method? 5. Determine the force in member bf using section method? 6. Determine the force in member of using section method? g 1 kN 3m 3m Simple Truss I d TTF truss 4 m 3m
Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi, determine the maximum load P that may be supported by the structure. (1) 6 ft 4ft O 15.75 kips 18.32 kips O 9.55 kips O 14.24 kips O 19.92 kips
please skip if you already did this
B1
a) Analyze the structure to determine the forces in each members of the truss shown in figure below by method of joints. State if the members are in tension or compression PI = (12W) where W = 41 P2 = (6W) kN b) Also analyze the truss by graphical method D 3m. 3m. B •6m. 6 m.
A: Without any solutions, identify the zero-force members. B: Determine the forces in the members identified by "x" using two sections ONLY. 70 KN S0 KN 50 KN 6 m 14 m= 16 m
For the truss shown, determine the maximum axial stress experienced. P= 70 Ex. (1.5P) = 1.5(70) = 105 (2.5P) = 2.5(70) = 175