Given the structure of the Indeterminate Static Portal as shown in the image above. Is known: E = 200 GPa and I = 262 x 10^12 mm4. By using the consistent deformation method: a. Write a compatibility equation if the vertical displacement reaction at C is used as a redundant b. Calculate the bearing reaction of the structure and draw the internal force diagram! 5 kN/m B El

Given the structure of the Indeterminate Static Portal as shown in the image above. Is known: E = 200 GPa and I = 262 x 10^12 mm4. By using the consistent deformation method: a. Write a compatibility equation if the vertical displacement reaction at C is used as a redundant b. Calculate the bearing reaction of the structure and draw the internal force diagram! 5 kN/m B El

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 4. Determine the value of the constant C in the stress function 0 = C{r?(x -0) + p?sin 0 cos 0 - r? cos? 0 tan a required to satisfy on the upper and lower edges of a triangular plate shown below. Evaluate the stress components o, Ty for a vertical section mn. Draw curves for the case a = 20° and draw also for comparison the curves given by elementary beam theory. m a y
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 2.4 mm and upward by v = 5.8 mm to new position Q′. Determine the shear strain γ at corner Q′ after deformation. Use c = 730 mm, α = 25°, and β = 65°.
From the previous problem, determine the shear stress 30 mmabove the neutral axis.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young’s modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work.
A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on. c) Determine the relative angle of twist o G-70 GPa # * 2m 450 kN.m B
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
Find the normal stress, shear stress, and bending deformation of the beam. For the cross-sectional area: by = 0.75 meter, d = 1 meter, tw = 0.10 meter, and tf = 0.15 m.
2. The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m?. The cross sectional area of each member is 0.01 m². Forces P1 and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 40 (c) 309 P1 P= 2kN 4m FIGURE Q2 a. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by perfoming complete calculations to justify your recommendation. b. After the client approved your recommendation in (a), it was found that the displacements occurred at node 1 is still high. As a result, you are required to modify the truss design in order to reduce the displacement at node 1 by minimum 15% on a condition that modules of elasticity, and the force remain unchanged. Justify your recommendation.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)