Answered: For the truss shown, determine the…

For the truss shown, determine the maximum axial stress experienced. P= 70 Ex. (1.5P) = 1.5(70) = 105 (2.5P) = 2.5(70) = 175 All cross-sectional area is 300 sq. meter. P is in kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the truss shown, determine the maximum axial stress experienced. 2.5P В 30° 1.5P 4m 45% A

Q: 6. A truss ABC is subjected to a load F=10KN at pin D. The outside and inside diameters of bar AB…

Q: Mz = 595 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross…

Q: Compute the vertical displacement of joints Band C for the frame shown in the figure. Given: /= 360…

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm2 and…

Q: Prob. 2. Using the Method of Consistent Deformation, analyze the truss shown below. Use E = 20,000…

A: To determine member forces using method of consistent deformation

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum…

A: Given Data: a = 7.5 m b = 4.2 m

Q: For the element and state of stress shown: a) Draw Mohr's circle. b) Determine the principle…

A: Mohr,s circle is used to find the stress components and it is a graphical representation of the…

Q: Q1. 1.) Determine the state of stresses at an orientation of 20 degree clockwise from the element…

Q: B | 0.75 m 2.07m The rigid bar AB of negligible weight is supported by a pin at 0. When the two…

Q: M₂ Answer: OH = psi M₂ H b

Q: Find the north axis and the moment of the second area Find both the triangular axis and the moment…

A: The following is the given information. My = 240 N.m Mx = 380 N.m Thickness of bottom flange = 1…

Q: Construct the reduced stiffness matrix of the shown truss, Fig. 3.Then determine the nodal…

A: Solution;

Q: Determine the stress in member CE. Assume load P = 8.571 kN and Area in steel is 24 mm^2. A 1.4 m…

Q: A 80 MPa 30° B 30 MPa 40 MPa

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A: a = 40KN b = 22KN

Q: A solid circular bar is fixed at point A. Thebar is subjected to transverse load V = 70 lb andtorque…

Q: 2. Determine the largest load P that can be applied to the frame without causing either the average…

Q: The couple M = 78 kip-in. is app section shown in a plane formin vertical. Determine the stress at…

Q: Derive an expression of the maximum statical moment of area, Q and its location from the given…

Q: Draw Mohr's circle and find: 1) Principle stresses and their direction. 2) Maximum Shear stress and…

Q: Ex,: A weight Causes a static deflection of 8.= 0.060 in ist in on a beam with sf stiffiess k=…

A: Given,Static diflection Sstatic = 0.060 in Sstatic = 0.06 x 12 ft…

Q: Four steel bars jointly support a mass of 25 x 103 kg. Initially the temperature is 250C. Bars A and…

Q: Four steel bars jointly support a mass of 25 x 10³ kg. Initially the temperature is 25°C. Bars A and…

A: Given, M = 25000 kg T1 = 25oC AA = AD = 480 mm2 AB = AC = 360 mm2 E = 200 GPa α = 11.7 x 10-6 /C

Q: The internal shear force V at a certain section of an aluminum beam is 40 kN. The beam's centroid is…

A: V = 40 kN, Location of Centroid from bottom = 54.4 mm, Moment of Inertia, Iz = 398300 mm4

Q: 1. Use stiffness matrix to compute reactions at boundaries and element force considering the…

A: As per policy, the solution will be provided for the first question only. For the answer of the…

Q: Question 1. The plane NN' makes an angle 0-30" with respect to the cross section of theprismatic bar…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to rete…

Q: Use method of consistent of consistent deformation to solve the horizontal displacement of joint D…

A: a = 40KN b = 22KN

Q: F y a What is the biggest Bending Stress? Beam is loaded the biggest bending moment is MB. Мв 3D 10…

Q: 5. The beam is subjected to the loading as in the figure below. Determine_the absolute maximum…

A: Calculate the support reactions at point A ∑FV=0RA=12×3×6=9 kN∑MA=0MA-12×3×6×13×3=0MA=9 kN-m

Q: 2.11 The stress function = Ax + Bxy + Cy provides the direct and shear stresses in a thin…

A: The given stress function is,ϕ=Ax2+Bxy+Cy2A,b are,u=2aC-vAEv=2BA-vCE

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: 4.10 Given: The truss shown is made up of links DE, CE, CD and BC. All four links have the same…

A: Given :

Concept explainers

Planar Stresses

Question

For the truss shown, determine the maximum axial stress experienced.

P= 70 Ex. (1.5P) = 1.5(70) = 105

(2.5P) = 2.5(70) = 175

All cross-sectional area is 300 sq. meter. P is in kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length.
Determine the maximum and minimum principal stresses, and the normal and shear stresses on plane AB. q=400lb/ft² + 300 lb/ft² tazt 0=45° + 8 49² Txy=-300 lb/ft² q=750 lb/ft²
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
Find the normal stress, shear stress, and bending deformation of the beam. For the cross-sectional area: by = 0.75 meter, d = 1 meter, tw = 0.10 meter, and tf = 0.15 m.
2. The 2- dimensional truss shown in FIGURE Q2 is made of material that has a modules of elasticity E = 150×10° N/m?. The cross sectional area of each member is 0.01 m². Forces P1 and P2 are acting as shown, Wall (e= 40°, P;= 8 kN) 2 (a) (b) 40 (c) 309 P1 P= 2kN 4m FIGURE Q2 a. You are required to design TWO (2) different system's fixing type of nodes 2, 3, and 4 to the wall. Then recommend the best option that provides the lowest displacement at node 1 by perfoming complete calculations to justify your recommendation. b. After the client approved your recommendation in (a), it was found that the displacements occurred at node 1 is still high. As a result, you are required to modify the truss design in order to reduce the displacement at node 1 by minimum 15% on a condition that modules of elasticity, and the force remain unchanged. Justify your recommendation.
In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.1 ksi, If t 1.9 in. and b= 3.8 in., 3 in. a. determine the largest P, which is vertical, the frame can 3 in. carry 30 b. determine the largest P, which is normal to AC, the frame can carry
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
What is the normal stress on the oblique plane due to the load P? 155 kip 7 in P = a = b = 4 in a = 37 degrees