Problem 2: Using the data from the table shown below here, solve for Force in N, Torque in N- m, and Calculate Shear Stress and Strain due to torque(torsion) for each case by following sample calculations shown in the Module 2 Lesson. Fill in the blacked-out columns with your answers. (You may need to create a new table). NOTE that the beam dimensions, and other required data is provided at the top of the table. Gauge Factor:2.04 Beam diameter: 9.97 mm (0.00997 m) Beam Radius: 4.985 mm (0.0004985 m) Force (N) Load (kg) (Load x 9.81 m.s2) 0 0.25 0.5 Torque (Nm) Shear Modulus for the beam: 79.6 GPa Bridge Connection: Full Torque Arm Length: 0.15 m Polar Moment of Inertia Output Voltage (μV) 0 130 260 Strain Reading (HE) 0 12 25 Calculated (shear) Stress (MN.m2) Calculated (direct) Strain (μ€)

Problem 2: Using the data from the table shown below here, solve for Force in N, Torque in N- m, and Calculate Shear Stress and Strain due to torque(torsion) for each case by following sample calculations shown in the Module 2 Lesson. Fill in the blacked-out columns with your answers. (You may need to create a new table). NOTE that the beam dimensions, and other required data is provided at the top of the table. Gauge Factor:2.04 Beam diameter: 9.97 mm (0.00997 m) Beam Radius: 4.985 mm (0.0004985 m) Force (N) Load (kg) (Load x 9.81 m.s2) 0 0.25 0.5 Torque (Nm) Shear Modulus for the beam: 79.6 GPa Bridge Connection: Full Torque Arm Length: 0.15 m Polar Moment of Inertia Output Voltage (μV) 0 130 260 Strain Reading (HE) 0 12 25 Calculated (shear) Stress (MN.m2) Calculated (direct) Strain (μ€)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Showing the figure as shown in figure 2 determine the following • A) Location of Neutral Axis from…

A: The figure with dimensions is given asTo find:-(A) Location of neutral axis from the bottom(B)…

Q: y 20 mm 30 mm 20 mm 10 mm 40 mm X mm

A: The dimensions of the section are given . The centroid is 34 mm above x - axis .

Q: Q2) Find the value of (X) so that rigid beam shown in Figure (2) remains in horizontal position.…

Q: Suppose we have a uniform beam that is 2.92 metres long has a flexural rigidity of 30254Nm². N Find…

Q: Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301 Nm². N Find…

Q: Structural Analysis The cantilever beam carries load as shown in the figure below. Compute the…

Q: a- 6.1 m, b- 4.1 m, c - 14.1 kN/m, d- 24 kN. d kN d kN c kN/m "b" m "b" m m FIGURE 3

Q: For the figure shown, a. Determine the location of the centroid measured from the bottom (?̅). b.…

A: Fig-1Rectangle:Base=75+30=105mmHeight=25+30=55mmFig-2Quarter…

Q: Deflection Given: the beam cross-section shown have the following cross-sectional properties f'c…

A: Gross moment of inertia(Ig)Critical internal moment(Mcr)Maximum service load(Ma)Critical moment of…

Q: Using double-integration method, the cantilever beam shown in the figure consists of a W530 x 74…

A: Given data E = 200 GPA = 2 × 105 N/mm2 I = 410 × 106 mm4

Q: steel beam is loaded as shown in the figure. Determine the following by using conjugate beam method:…

Q: 6. A simply supported beam, of diameter 12 mm, is loaded as shown in the figure below. Using double…

A: Consider the free body diagram as;

Q: 3) Nails are used to connect three boards to form a beam as shown in the figure. Each nail has a…

A: Basically, a shear force is a force that acts parallel to a body's surface or cross-section, such as…

Q: 707. A couple M is applied at the propped end of the beam shown in Fig. P-707. Compute R at the…

Q: The truss shown is one of several supporting an advertising panel. Consider the wind load P = 820 N…

A: Step 1:Step 2:Step 3:Step 4:

Q: Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301Nm. Find the…

Q: A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform…

Q: 6. A simply supported beam, of diameter 12 mm, is loaded as shown in the figure below. Using double…

A: Consider the free body diagram as;

Q: This is an exercise to illustrate the effects of mesh refinement on a 1-d rod. To estimate the…

A: Do = 3m R 1.5m α = 0.3 So, d = 0.3x3 = 0.9m r = 0.45m L= 5m

Q: Suppose we have a uniform beam that is 3.40metres long has a flexural rigidity of 31915N Find the…

Q: The figure shows a cantilever of length L= 4 m consisting of steel angles size of 100 x 100 x 12 mm…

A: Introduction- A cantilever is a horizontal extending rigid structural component with just one end…

Q: A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and…

A: For a wooden bar beam arrangementThe beam is formed by nailing wooden bar and each nailshearing…

Q: Determine me 1. Locate the centroid of the bent wire shown in the figure. The wire is homogenous and…

Q: The figure shows a sign hanging from a beam anchored to a wall by two cables. In an element of the…

Q: 1. State in words the condition for rotational equilibrium. 2. In exercise physiology studies, it is…

A: 1. The condition of rotational equilibrium is that the vector sum of all the moments acting on the…

Q: A tapered circular varying from 20 mm to 10 mm is

Q: Case 1: Uniform beam under distributed load. In the shown Figure, a uniform beam subject to a…

Q: solve step by step in digital format Solve the following exercises by the conjugate beam method A…

A: A cantilever beam is given with UVL load zero at free end and 6k/ft at the fixed end.The span of the…

Q: stress and strain

Q: Note: this is not a graded question please help us to understand how to solve this sample question…

A: To find force in member bd

Q: Problem #2 The bar shown below has uniform cross section and material properties throughout. In…

Q: Note: this is not a graded question please help us to understand how to solve this sample question…

A: To find force in member ab

Q: concentrated loads P. A horizontal beam A B of length L is supported by a fixed support at its left…

Question

100%

Problem 2: Using the data from the table shown below here, solve for Force in N, Torque in N-
m, and Calculate Shear Stress and Strain due to torque(torsion) for each case by following
sample calculations shown in the Module 2 Lesson. Fill in the blacked-out columns with your
answers. (You may need to create a new table).
NOTE that the beam dimensions, and other required data is provided at the top of the table.
Gauge Factor: 2.04
Beam diameter: 9.97 mm (0.00997 m)
Beam Radius: 4.985 mm (0.0004985 m)
Force (N)
Load (kg) (Load x 9.81 m.s²)
0
0.25
0.5
Torque
(Nm)
Shear Modulus for the beam: 79.6 GPa
Bridge Connection: Full
Torque Arm Length: 0.15 m
Polar Moment of Inertia:
Output
Voltage
(UV)
0
130
260
Strain
Reading
(HE)
0
12
25
Calculated
(shear)
Stress
(MN.m2)
Calculated
(direct)
Strain
(μ€)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given information

VIEW

Step 2: Force calculation

VIEW

Step 3: Torque calculation

VIEW

Step 4: shear stress calculation

VIEW

Step 5: Direct strain calculation

VIEW

Solution

VIEW

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Needs Complete typed solution with 100 % accuracy.
3. Please make work and answers legible and easy to find. Thank you!
1. Please make work and answers legible and easy to find. Thank you!
Suppose we have a uniform beam that is 3.40metres long has a flexural rigidity of 31915N Find the deflection of the beam in millimetres if the beam is under a uniform load of 24Nmand is supported with simple supports at both ends. Fill out the table below with your answers. x�-coordinate Deflection (mm��) x=0.14 y(x)�(�) = x=1.12 y(x)�(�) = x=1.80 y(x)�(�) = x=2.65 y(x)�(�) = x=3.06 y(x)�(�) = Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within ±0.0005±0.0005 of the correct answer to be considered correct.
(((Strength of Materials))) Please solve it very quickly Frist tow number 18 Frist three numbers 187 1.Read questions carefully. 2. Draw neat, labelled diagrams. 3.Write relevant equations. 4.Be clear and specific and include units in answers. 5.Give explanatory notes where necessary.
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. A pulley of diameter D = 720 mm is mounted on a shaft that has a diameter of d = 80 mm. The pulley is prevented from rotating relative to the shaft by a shear key. The cross section of the shear key is square with dimension a = 10 mm. The length of the shear key (i.e., the dimension into the screen) is 110 mm. The allowable shear stress in the shear key is 200 MPa. If T2 = 0.20T1, what is the maximum allowable belt tension T1? T1 Pulley -Shear key D Shaft T2 Answer: T1 = kN
For the case of the simply supported beam presented in Figure 1 and inaccordance with the truss analogy, describe how the bending moments and the shear forces are transferred through its span to the supports. Based on the truss analogy model, what are the likely causes of brittle failure? The figure is given in the pic.
Subject : Structural Theory Use P= 60 Please solve this with complete and detailed solution. Make your solution readable, clear, and understandable. Note : Please don't post it on google because I don't want my instructor to seet it. Thank you so much.
Show detailed and complete solutions. Draw illustrations. Follow the decimal places required
Note: this is not a graded question please help us to understand how to solve this sample question thank you very much A.) Select the answer that most nearly gives the absolute value of axial force on member "bd" from the virtual structure for vertical displacement of joint d. choices: 1.02 0.89 0.36 0.78 -0.12 -1.20 -2.87 -2.10 Note: please base your answer on the given choices thank you very much and also this is not a graded question but a sample question only we need your help so that we can understand this problem set
Need correctly in proper handwriting.
For the 2d coordinate system below, complete the following: a) Break up the force vector into Fx and Fy components; show these components on the figure. Add a superscript to each component to indicate whether they are acting in the positive (+) or negative (-) direction b) Draw a position vector from the origin (0) to the tail (point a) of the force vector c) Break up the position vector into rx and ry components; show these components on the figure Add a superscript to each component to indicate whether they are acting in the positive (+) or negative (-) direction d) Calculate the "moment" of force F about the origin by multiplying F times its perpendicular distance from the origin (ry), and add the product of Fy times its perpendicular distance from the origin (rx). Assume that a counterclockwise rotation about the origin is a "positive" moment. Think of rx as a string connected to the origin. If you pull the string in the direction of d, will that cause a clockwise (-) or…