Problem 2 Three reservoirs are connected by a piping system as shown in Figure 1. Find the discharge into or from the reservoir B and C, if the rate of flow from reservoir A is (55+X) liter/s. Also find the height of water level in reservoir C. Assume the following data: X=7 Pipe 1 3 Length (m) 1Х00 600 700 Diameter (mm) 400 300 200 Friction factor 0.008 0.008 0.008 A B Pipe -1 Pipe- 2 ZA= 45 m Pipe-3 ZB= 40 m C Z. Datum Line Figure 1

Problem 2 Three reservoirs are connected by a piping system as shown in Figure 1. Find the discharge into or from the reservoir B and C, if the rate of flow from reservoir A is (55+X) liter/s. Also find the height of water level in reservoir C. Assume the following data: X=7 Pipe 1 3 Length (m) 1Х00 600 700 Diameter (mm) 400 300 200 Friction factor 0.008 0.008 0.008 A B Pipe -1 Pipe- 2 ZA= 45 m Pipe-3 ZB= 40 m C Z. Datum Line Figure 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3 m P Lower reservoir 100 m 1 m Upper reservoir 10 m

Q: 13. For the reservoir-pipe system shown in the figure given below, by considering the liquid as…

A: Solution:

Q: A reservoir has a water height (H) of 15 meters (from the surface to the centerline of the reservoir…

Q: Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the…

A: Given data: h1=0.9 m h1=1.6 m h1=3.9 m Width of the gate, b= m depth of the gate, d=5 m Angle θ=60°…

Q: 4. If viscous effects are neglected and the tank is large, determine the flowrate from the tank…

Q: Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter…

Q: A triangular pipe network is shown in the figure. Q=70 r=1 B r=2 Q=30 Q=100 A C The head loss in…

Q: As shown in the figure below, water behind a dam enters an intake pipe at a pressure of 24 psia and…

A: To solve this problem, first we need to calculate the specific gravity. Then the Bernoulli equation…

Question

Problem 2
Three reservoirs are connected by a piping system as shown in Figure 1. Find the discharge
into or from the reservoir B and C, if the rate of flow from reservoir A is (55+X) liter/s. Also find
the height of water level in reservoir C. Assume the following data:
X=7
Pipe
1
3
Length (m)
1Х00
600
700
Diameter (mm)
400
300
200
Friction factor
0.008
0.008
0.008
A
B
Pipe -1
Pipe- 2
ZA= 45 m
Pipe-3
ZB= 40 m
C
Z.
Datum Line
Figure 1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. What is the ground water travel time from well MW1 to well MW2 (days) according to the following figure's condition? (Hint: Solve by Darcy's Law) - TOC stands for Top of Casing, and is an elevation with respect to a common datum DTW stands for Depth to water, which is the distance from the TOC to the water table MW1 MWI MW2 L = K= 900 ft TOC (ft) 18 ft/day 0.24 1052.6 1045.3 DTW (ft) 12.5 14.2 MW2
9. A tank as shown in figure below compose of hemispherical at the top, cylinder at the middle and cone at the bottom is contain of full water, A 100 mm 4 orifice located at the bottom (C = 0.62), compute for; A) Time to drop the water from 7m to 4 m B) Time to empty the half of water in the tank C) Time to empty the whole tank 4mp 2 m 3 m 2 m
36. Darcy's law gives us the volume flow rate-volume per time (for example, cubic meters per day, m³/day). Another way to express volume is on a per-unit-area basis. For example, if we have a 1-m’ cube, we know its 3 3
Water flows through a pipe as shown in the figure. The pressure at points 1 and 2 respectively is 1.85 × 105 Pa and 1.10 x 105 Pa. The radius of the pipe at points 1 and 2 respectively is 3.20 cm and 1.40 cm. If the vertical distance between points 1 and 2 is 2.75 m, determine the following. (a) speed of flow at point 1 m/s (b) speed of flow at point 2 m/s (c) volume flow rate of the fluid through the pipe m³/s P₂ y
Use the following given values to solve problems, unless otherwise stated. Ywater = 9790 N/m³ = 62.4 lbf/ft°; g = 9.81 m/s? = 32.2 ft/s²; 1 hp = 550 lbf-ft/s = 746 Watts Problem-1 Water is pumped from the large tank through a uniform diameter pipe (d = 3 in.) and exits as a free jet (refer figure-a). The plot of the flowrate (Q) versus pump-head (hp) is a straight-line graph that passes through points (3, 16) as shown in figure-b. If the pipe friction head loss is, hf = 7V:/2g, where V is the average fluid velocity in the pipe, find a) the equation that relates hp and Q; b) flowrate and c) If the pump is 75% efficient, what horsepower is needed to drive it? Assume steady, incompressible flow. Ignore kinetic energy correction factor (a). 12 ft Pump %3D (a) 16 3. Q, ft°ls (b) dy
Determine the natural frequency of the simple spring-mass system shown.
Problem 1.2 Two water tanks are connected to each other through a mercury manometer with inclined tubes as shown in figure. The value of theta is degree. (Take g=9.81 m/s²) Water (p.= 1000 kg/m³) Tank A P=20 kPa Tank B P = 40 kPa Mercury (P = 13600 kg/m³) 26.8 cm
Water flows at a rate of 28 L/s through a horizontal pipe whose diameter is constant at 3 cm. The pressure drop across a valve in the pipe is measured to be 2 kPa, as shown in the given figure. Determine the irreversible head loss of the valve and the useful pumping power needed to overcome the resulting pressure drop. Take the density of water to be p-1000 kg/m³ Water AP=2 kPa The irreversible head loss of the valve is The useful pumping power needed to overcome the head loss is m. W
With velocity of 7 m/s in the 330 mm diameter pipe in the figure shown, determine the discharge in pipe 3 in m3/s. Assume f = 0.046 for all pipes and neglect minor losses. The following are the properties of each pipe: Pipe 1 (Length=572 m, Diameter = 330 mm) Pipe 2 (Length=344 m, Diameter = 536 mm) Pipe 3 (Length=391 m, Diameter = 963 mm) Pipe 4 (Length=867 m, Diameter = 317 mm) Pipe 5 (Length=991 m, Diameter = 310 mm) Round your answers in 3 decimal places.