Problem 12 Knowing that P = 5.2 kN, determine the factor of safety for the structure shown. Use E = 200 GPa and consider only buckling in the plane of the structure. F.S. = 1.5 P 70% B 22-mm diameter 1.2 m 18-mm diameter 1.2 m

Q: Problem No. 2: Determine the x and y-coordinate of the centroid of the shaded area.

A:

Q: The six standard views in orthographic projection are front, top, bottom, and what?

A: Answer : Left view Right view  Rear view

Q: 4" 8" 6"

A: Solution:- Centroid of the given section: Table for calculation  Area inch2 x- coordinate inch y-…

Q: It is a pictorial representation that combines height-width-depth/length into a single view with30…

A:

Q: TOP VIEW 60 80 40 20 30 50 35 15 10 FRONT VIEW RIGHT SIDE VIEW

A:

Q: Law of Cosines (Engineering):

A: Law of cosines signifies the relation between the lengths of sides of a triangle with respect to the…

Q: In detail, write about the introduction to 3D Shearing transformation.

A:

Q: - What are illustrative drawings? 2.- What is the most widely used type of illustrative drawing in…

A:

Q: continue dimension and baseline dimension?

A:

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A:

Q: Show Isometric View.

A: Answer  We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: Discuss the procedure for performing 2D conformal coordinate transformations?

A: Solution: There are basically 3 steps that are used in the procedure of 2D conformal coordinate…

Q: Civil Engineering Orthographic and isometric projections are two basic types of graphic projection…

A: The statement Orthographic and isometric projections are two basic types of graphic projection is…

Q: Show me this drawing Step by step how to draw it. thank you 25 105 30 ø16 60° 40 60 70 it's from…

A: To Determine Steps to be used in drawing the given figure in CADD software.

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: Given the isometric view of the cut block objects shown, use rectangular grid paper to sketch a…

A:

Q: Using multiview, the user can layout drawings in different paper sizes at the same time. O True…

A: A multi-view drawing is one that shows two or more two-dimensional views of a  three-dimensional…

Q: 60 Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: WE HAVE TO DRAW THE LEET SIDE , FRONT VIEW AND TOP VIEW   Looking at X direction, we conclude that…

Q: what research should be done next when beam bending experiment goes satisfactory write a small…

A: The experiment of concrete to obtain the mechanical and durability properties. The mechanical…

Q: parametric surfaces play a role in 3D graphics, especially in CAD

A: Parametric surfaces play a crucial role in 3D graphics, particularly in Computer - Aided Design…

Q: 9. Which among the following is a standard scale for a similitude?

A: In fluid mechanics, we use similarity as a similitude  This means two shapes have the geometrical or…

Q: re text height , arrow size be easily adjusted based on the size of the object? autocad 2.How about…

A: 1. Text can be re-formatted or adjusted for an individual dimension object by selecting the object…

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: Calculate the shear force and bending moment diagrams with manual calculation and verify using Space…

A:

Q: The Global Coordinate System (GCS) is an acronym for Global Coordinate System. What motivated the…

A: Global Coordinate System is an absolute reference system which is used to define locations of nodes…

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: Exercise 1.5: Third Angle Projection type is displayed. Estimate the dimensions. Draw the Visible…

A: To draw the right side view of the given figure.

Q: What are the types of coordinate system? Illustrate with neat figure.

A: Generally two types of coordinate systems viz, Catesian Coordinate. Polar Coordinate.  Cartesian…

Q: Exercise 1.6: Estimate the dimensions. Draw the Front view, Top view and Right view. Draw the…

A: Question related to the engineering drawingsmodel is given  FINDFront viewtop viewright…

Q: Given the following isometric drawing, how many edges are drawn as points in the right side view of…

A: ASKED: To determine the number of edges of the given isometric drawing that are drawn as points in…

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: 5. In editing dimension lines, why is it important that the offset of origin must be edited…

A: The dimension line is a fine, dark, solid line with arrowheads on each end. It indicates direction…

Q: A line CD starting at any point, C, is 8 m long bears N 35° W, and slopes downward from C to D at…

A:

Q: 4. Complete the accompanying set of profile notes and perform the arithmetic check. Provide a sketch…

A: The levelling terms and formula. BS = Back sight The first measurement taken in a survey. It is the…

Q: graphical presentation for 3D shearing transformation.

A: It is change looking like the article. It is likewise called as deformity. Change can be in the x -…