Exercise 1.5: Third Angle Projection type is displayed. Estimate the dimensions. Draw the Visible Feature Lines of the Right view for the model. Draw any Hidden lines if needed. Identify the view that should display the most information about the illustrated model. ||| # L 1 It

Q: Create a 3-dimensional isometric projection based on the 2-dimensional orthographic projection below

A:

Q: Determine the coordinates of the centroid of the lines used as boundaries of the ea shown in Problem…

A:

Q: Problem Solving: 1. From the given frame shown it is supported by a hinged at A and a roller at C.…

A: To find deflection,  unit load method has been used.

Q: The "RIGHT HAND RULE " of 3D drawing indicates that the Z axis is poiting where?

A: In right hand rule,  If thumb is x axis and index finger is y axis Then middle figer show the…

Q: 51 35 88 73 53 15 20 25 „16 64 _15 38 75

A: Given isometric figure is,

Q: The following are the methods of plotting contour lines except: template method estimation…

A: The methods of plotting contour lines are: Estimation method Graphical method Template method…

Q: Determine the coordinates of the centroid of the lines used as boundaries of the area shown in…

A:

Q: TOP VIEW 60 80 40 20 30 50 35 15 10 FRONT VIEW RIGHT SIDE VIEW

A:

Q: Show the dimensions of the views shown.

A: The dimension of the given figure is shown below.

Q: Matching Directions: Match each description of locating points when creating planar entities in the…

A:

Q: Problem Solving: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415…

A:

Q: Why is GCMS considered a 3D analytical technique?

A: It stands for Gas chromatography - mass spectrometry. It is a method for identifying different…

Q: Locate the centroid x and y of the cross sectional area of the angle bar

A: Given:- An angle bar is shown  To determine:- The centroid x and y of the cross-sectional area of…

Q: Given a 256 x 256 pixel image, if a projection is taken every 1 degree in a complete circle, how…

A: verticalheight of image=256horizontal height of…

Q: 99 # 日 P

A:

Q: Draw the orthographic side view of the given image with proper dimensions

A: Top view and front view is given, we need to draw side view

Q: Please solve question 3. An example has been given of a solved orthographic view. Given two…

A: We need to construct an Auxiliary view

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: TOP VIEW 150 20.0 35.0 100 FRONT VIEW SIDE VIEW ORTHOGRAPHIC VIEW 55 0

A: Given data  Top view ,front view, side view  To find : isometric view

Q: By using the figure below, reproduce this by using the relative rectangular coordinate entry. You…

A: Required To reproduce the given figure in question and to give the commands used to draw in AutoCAD.…

Q: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275…

A: Cantilever beam: A cantilever is a rigid Structural element that can be extended horizontally and…

Q: The previous, zoom :command is used to Its usefulness is to enlarge the drawing page. This command…

A: Shift + P is used to get previous zoom in the autocadd some times it is very useful for designing…

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the D Drawing (ometric View) of the…

A: Isometric view is the 3 dimentional view in 2D plane.  Below is the attatched isometric view of the…

Q: Q.1) For the area below, find the coordinates of the centroid. 300 mm 400 mm 300 mm 300 mm

A:

Q: in engineering

A: Consider a rectangular section where X and y are placed in 2nd and 4th quadrant respectively.

Q: From the figure shown, determine the following: y L, L4 CE h, h7 he h2 hs he he Distance of the…

A: To determine Distance of Centroid from x-axis.

Q: Top, Front and Side view of this sketch.

A:

Q: Exercise 1.6: Estimate the dimensions. Draw the Front view, Top view and Right view. Draw the…

A: Question related to the engineering drawingsmodel is given  FINDFront viewtop viewright…

Q: 16 cm 8 cm 8 cm 8 cm ·X

A:

Q: Sketch the othrographic views: plan view, elevation view, and end view on paper.

A: The given view is an isometric view. Taking the front direction where 12 is written, the…

Q: ure in your module. Indicate the scale that you used in drawing the map. Note that the contour map…

A: The boundary of the object or the outline of  the body is known as contour.

Q: (Top View, Front View, Side View)

A:

Q: Sketch an ISOMETRIC DRAWING from the attached orthographic projection. Follow the assigned…

A:

Q: 1. Draw the front view in the direction of F and the top view in the direction T of the given…

A: As in problem it is given that the front view and too view has to be drawn using 1st angle…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 195 mm 50 mm 50 mm 455 mm

A: Consider the figure,