PROBLEM 10.15 12 mm A column with the cross section shown has a 4 m effective length. Using a factor of safety equal to 2.8, determine the allowable centric load that can be applied to the column. Use E = 200 GPa. 6 mm 250 mm 12 mm 150 mm

PROBLEM 10.15 12 mm A column with the cross section shown has a 4 m effective length. Using a factor of safety equal to 2.8, determine the allowable centric load that can be applied to the column. Use E = 200 GPa. 6 mm 250 mm 12 mm 150 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A steel column with the cross section shown has a 14.7-ft effective length. Using Allowable Stress…

A: The effective length is .The yield stress is .The modulus of elasticity is .

Q: Determine the axial load in rod (1).

Q: A solid plastic rod has a diameter of d = 30 mm and a length of L = 625 mm. An axial load of P = 21…

A: Given: Diameter, d = 30 mm Length, L = 625 mm Axial load, P = 21 kN Elastic modulus, E = 2.4 GPa…

Q: Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a…

A: Given: The length of column, Le = 7 m The elastic modulus, E = 200 GPa The moment of inertia about…

Q: A stiff, square, thick rubber plate (m = 502 g) sits on the round mouth of a jar, completely…

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick,…

Q: The steel frame (E = 200 GPa) shown has a diagonal brace BD with an area of 1920 mm². Determine the…

A: Given Data- Area A =1920mm2 E=200GPa Change in length of BD =1.9mm We have to find Load P

Q: Design a hollow cylindrical cast iron column with both ends fixed to carry an axial load of 250 kN,…

A: Axial loadLength of the columnFactor of safetyCrushing strengthRankine constantIf internal diameter…

Q: 10.14. If P = 1000 Kg find the diameter of the elements subjected to compression to avoid buckling.…

Q: When a column of same material and size is tested, under. end conditions it carries minimum…

Q: The rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by…

Q: A 16-ft-long column that is effectively pin-supported at both ends can be made by gluing together…

A: The moment of inertia for the first configuration can be determined as,

Q: A column of 6.7-m effective length is obtained by connecting four L89 x 89 x 9.5-mm steel angles…

A: given data effective length (Le ) = 6.7 m steel angle = L89×89×9.5-mm σy = 345 MPaE = 200 GPa

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: Q6 A pivot-ended solid steel bar having a diameter of 50 mm and a length of 2.0 m will be used to…

A: To find: a) The value of maximum safe compressive load. b) The implied value of eccentricity. Given…

Q: A 3 meters long column has a circular cross-section of diameter 3 cm. Taking the factor of safety as…

Q: A 3.5-m long column with rectangular cross section of 4 cm x 3 cm is under an axial compressive load…

Q: Determine the critical load of a pin-ended wooden stick that is 3 ft long and has a 3/16 × 1 1/4-in.…

Q: A mild steel strut is of single angle section 100 mm x 75 mm x 8 mm. Its length is 3m wiun both ends…

A: Stress When body is subjected to a load then body will get deform but body will resist the…

Q: Problem 4.54 I Review Part A The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992…

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=88 kNe=0.025 mb=0.180 md=0.240 m

Q: A square column with side dimension of 80 mm rests on top of a timber footing. It is determined that…

Q: 5. Two C310x45 channels are latticed together so they have equal moments of inertia about the…

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Determine the axial load in rod…

A: It is very basic question of mechanics. Used concept is equation of static equilibrium conditions in…

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick,…

A: Given ,Rigid bar ABC is supported by pin connected bar 1.Width = 1.625 in.Thickness = 1.125…

Q: If the deck is prevented from sidesway, determine the greatest weight of the load that can be…

Q: A gazebo is planned to be constructed in a community park as an additional shelter for visitors from…

A: Solution: Given Data: A=7200 mm2SR=0.026E=200 GPaσy=233 MPaFOS=1.67K=0.7 (for Fixed-pinned end)

Q: 400-m bar of 16 x 60-mm rectangular crosSs section consists of two mild-steel layers, each 5 mm…

A: Given dataE=200GPaδm=1.4σ1(mild Steel)=240MPaσ2(tempered steel)=600MPaL=400mm ***As per our company…

Q: A steel rod 4 m long and 40 mm diameter is used as a column. Determine the crippling load by Euler’s…

A: L= 4 md=40 mmE=2×105 N/mm2Pc=π2EILef2I=π64×404=125663.706 mm4aBoth end are hinged In this case…

Q: A 1.2 meters long column has a square cross-section of side 2.8 cm. Taking the factor of safety as…

Q: diameter brass rod. In order to reduce the weight of the member by 25%, the solid rod is replaced by…

Q: A rectangular wooden column (E = 12 GPa) of 3 m have as dimensions shown. Determine a critical load…

Q: Two solid cylindrical rods support a load of P = 25 kN as shown. Determine the axial load in rod…

Q: Required information A 1-in.-square aluminum strut is maintained in the position shown by a pin…

A: Solution: Given Data: A=1 in2LAB=3.4 ftE=10.4×106 psiFOS=3.2 To Find; The magnitude of the…

Q: 4. Repeat problem 3 assuming that the column is made of wood for which E = 10 GPa. Ans. 81.34 mm

A: Given Force, F = 40 kN Length, L = 3 m E = 10 GPa Find Length, b

Q: 6. Repeat problem 5 assuming that one end is fixed and the other hinged

A: The buckling load for a column having its ends hinged, can be calculated using the formula given…

Q: 2.45 A reinforced concrete column 200 mm in diameter is designed to carry an axial compressive load…

A: Given that: Diameter of the concrete column is 200 mm. It is designed to carry 320 kN = 320*100 N…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

100%

PROBLEM 10.15
12 mm
A column with the cross section shown has a 4 m effective length. Using a
factor of safety equal to 2.8, determine the allowable centric load that can be
applied to the column. Use E = 200 GPa.
250 mm
6 mm
12 mm
-150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two solid cylindrical rods support a load of P = 28 kN as shown. Determine the axial load in rod (1). 3.8 m 4.6 m (1) 5.6 m 3.3 m O 21.47 kN O 31.42 kN O 27.17 kN O 22.76 kN O 28.61 KN B P
An aluminum structural tube is reinforced by bolting two plates to it as shown for use as a column of 1.3-m effective length. Knowing that all material is aluminum alloy 2014-T6, determine the maximum allowable centric load. (Round the final answer to one decimal place.) 6 mm 8 mm 54 mm 8 mm 8 mm 34 mm 8 mm 0 6 mm The maximum allowable centric load is 274.238 KN.
Please answer clearly with free body diagram don't waste my question I will vote it up for your effort thanks.
A rigid bar ABCDE is hinged at end A and supported by three cables at points B and C and D Cable C has a nominal diameter of 12 mm and an area of 76.7 mm2, and an ultimate load of 102 KN. Cable B and D has a diameter of 20mm and an effective area of 173 mm2, and an ultimate load of 231 Kn. The cables have an effective modulus of elasticity 140 GPa and a thermal expansion coefficient of  = 12 x 10-6 / ºC. A charge P acts at the end E of the bar. a) What is the allowable load P if the temperature increases by 60ºC and a safety factor of at least 5 is required against your ultimate charge? b) Determine the displacement of point E on the bar.
Two solid cylindrical rods support a load of P = 19 kN as shown. Determine the axial load in rod (1). 3.8 m 4.6 m (1) 5.6 m 3.3 m 18.15 KN 20.03 KN 21.56 kN 15.44 kN 14.52 KN B (2)
A square column with side dimension of 50 mm rests on top of a timber footing. It is determined that the column carries an axial load of 417 kN. If the punching strength of concrete is 10.05 MPa, determine the minimum thickness (mm) of the footing.
Question 3. Determine the crippling load for a I-section of dimensions 20 cm × 10 cm × 2 cm and of length 5 m when it is used as a strut with both of its ends fixed. Take E = 2 × 105 N/mm2.
Question 3. Determine the crippling load for a I-section of dimensions 12 cm × 12 cm × 2 cm and of length 5 m when it is used as a strut with both of its ends fixed. Take E = 2 × 105 N/mm2.
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A
I need the answer as soon as possible
Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: Ta=200 MPa Support brackets: (Gharn n=150 MPa d-12 -35m 3m 20 mm smm Member AB- 10 mm Support Bracket- Support Bracket Conection detail at EpetA
Question 4