A 16-ft-long column that is effectively pin-supported at both ends can be made by gluing together three identical 1.5" x 4.5" planks in either of the two configurations shown. Determine the Euler critical load for each configuration. The planks are Douglas fir (E = 1900 ksi).

Q: A 27- ft-long column is made of aluminum alloy 2014-T6. A. 5.25 in. *0,5 in. -x 10 in. *0.5 in. *…

A:

Q: Question 3 A column of 7 m effective length is to be made by welding two 228 x 12 mm plates to a…

A: Given: The length of column, Le = 7 m The elastic modulus, E = 200 GPa The moment of inertia about…

Q: 2. For the structure shown below, calculate the force in the cable and the reactions at pin A. Cable…

A:

Q: Determine the critical load (Pcr) for a fixed-pinned column, with a circular cross section of 40 mm…

A: Diameter, D= 40 mm L= 1600 mm E= 207 GPa= 207(1000) MPa= 207000 MPa Sy= 920 MPa Column type:…

Q: For which one of the following columns 47 EI Euler's buckling load

A: Explanationas we know that critical buckling load is given asPcr=π2EIle2Wherele→Equivalent lengthFor…

Q: Design a hollow cylindrical cast iron column with both ends fixed to carry an axial load of 250 kN,…

A: Axial loadLength of the columnFactor of safetyCrushing strengthRankine constantIf internal diameter…

Q: Determine the critical buckling load for a column that is pin supported?

A: Consider the diagram shown below for a hinged column.

Q: When a column of same material and size is tested, under. end conditions it carries minimum…

A:

Q: 2. A column is made of steel (E = 210 GPa) and has a rectangular (20 mm x 10 mm) cross section.…

A:

Q: Determine the crippling load when a column of diameter 8 cm and length 5 m is hinged at both ends.…

A: Given,   Diameter = d = 8 cm = 0.08 mLength = L = 5 mYoung's modulus = E = 210 GPa = 210 × 109 Pa…

Q: The A-36 stee (Fy= 250 MPa) W 200 x 46 member shown in Fig. is to be used as a pin- connected…

A: Given data: The length of the beam is, L=4 m. The yield stress is, Fy=250 MPa. Refer to the table…

Q: For a W14 x 53 column of A992 steel, 45 ft tall, determine the available load capacity when the ends…

A: Given     Length, L = 45 ft                     = 13.71 m Find    Calculate the Load capacity

Q: Determine the internal load of element 3. Note that elements BG and CF are independent. a = 3, b…

A:

Q: L P The axially loaded member is pin-connected at one end and fixed at the other. The member has a…

A: There is pin connected at one end and fixed support at other end.The cross sectioin is square of…

Q: A 3 meters long column has a circular cross-section of diameter 3 cm. Taking the factor of safety as…

A:

Q: 12. A column of length 18" and a diameter of 0.25" was tested with both ends pinned. The measured…

A: Given- Length (L) = 18  inch Diameter (d)  = 0.25 inch E = 29000 ksi = 29000000 lbs/in2 Case 1 -…

Q: Determine the critical load of a pin-ended wooden stick that is 3 ft long and has a 3/16 × 1 1/4-in.…

A:

Q: 8. Select the lightest W shape that will act as a column 12 m long with fixed ends and support an…

A: To find : select the lightest shape that will act column. Given : axial loadP=700 KN proportional…

Q: Problem 4.54 I Review Part A The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992…

A:

Q: Determine the critical axial buckling load for an 8 3/4 x 12 inches glue-laminated column braced at…

A: In the question , given that, E = young modulus of elasticity (1.8×106psi) dimension of column ,…

Q: Q1- How much power must be supplied for the pump to maintain of 250mm of mercury vacuum and 275 Kpa…

A:

Q: The column in Fig. is made of aluminum alloy 2014-T6 and is used tosupport an eccentric load P.…

A: The expression for the radius of gyration is: The slenderness ratio for the column is: Here, K…

Q: A square column with side dimension of 80 mm rests on top of a timber footing. It is determined that…

A:

Q: 5. Two C310x45 channels are latticed together so they have equal moments of inertia about the…

A:

Q: Determine the nominal compressive strength (P.) of a W12x96 column with no bracing and an unbraced…

A:

Q: If the deck is prevented from sidesway, determine the greatest weight of the load that can be…

A:

Q: 400-m bar of 16 x 60-mm rectangular crosSs section consists of two mild-steel layers, each 5 mm…

A: Given dataE=200GPaδm=1.4σ1(mild Steel)=240MPaσ2(tempered steel)=600MPaL=400mm ***As per our company…

Q: Determine the internal load of element 3. Note that elements BG and CF are independent. a = 4, b…

A:

Q: Determine the buckling strength of a W 12 x 50 column with a length of 25 ft. For the major axis…

A: Given Data:Column type: W12x50 (wide flange section)Column length (L) = 25 ftMajor axis (x) - Pinned…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.