Problem 1.6 Determine the magnitude and coordinate direction angles of the resultant force, and sketch this vector on the coordinate system.

Q: Q4. Determine the magnitude of the resultant force and its direction measured counterclockwise from…

A: Given

Q: One Kilogram of steam is contained in a piston/cylinder device at 800 kPa and 200°C. (a) If it…

A: Given that: 1 kg of steam is contained in a piston cylinder arrangement at 800 kPa and 200 °C. (a)…

Q: Differentiate clearly between tidal stream and range powers, and prove that the mean powver produced…

A:

Q: Determine the angle through which end A rotates, if a torque of TA = 88 N-m is applied at A. Note:…

A:

Q: 6. Steam is admitted to the cylinder of an engine with an average pressure of 25 bar. The piston…

A: The data given in this question are below: The average pressure is, P=25 bar. The piston diameter…

Q: (Force on plane surface) The rectangular gate CD of the figure below is 1.6 m wide and 2.0 m long.…

A:

Q: Part B Find M, the magnitude of the moment, and 0, the angle between r and the force F.

A: A position vector for a line representing with two end points can be obtained by subtracting the…

Q: An airplane weighing 8,000 Ib has an upward acceleration of 3g when land Ma• 24,000 lb A w-8,000 lb

A:

Q: 3. Find the moment of inertia about X-X axis. 6 in. 0.5 in. 4 in. 0.5 in. K

A: find the moment of inertia about x-axis.

Q: The slider block A is moving downward at v₁ = 7 m/s. (Figure 1) Figure B 250 mm 400 mm 30° D 300 mm…

A:

Q: (CLO-4] A rigid tank initially contains 50L of air (Ideal gas) at 400 kPa and 25°C. A wheel…

A: GivenP1=400kPaT1=25oCV=50L=0.05 m3W=-150kJ -ve sign  for work is done on the systemQ=-30kJ  -ve sign…

Q: A machine supported symmetrically on four springs has a mass of 160 kg. The mass of the…

A:

Q: Displacement Volume - Retraction 11 Calculate the volume of the cylinder during retraction.…

A:

Q: A 2.5 cm diameter HDPE cord (whose properties Fig. 5 are listed in Fig. 5) that is initially 25 cm…

A: Given data is

Q: For the instant represented, link CB is rotating counterclockwise at a constant rate N = 4.4 rad/s…

A: The angular velocity of link CB is ωcb=4.4 rad/s  (counterclockwise)

Q: A gas with density 1.3kg/m and dynamic viscosity 4air = 1.1 x 10-5Pa. s flows past a flat plate of…

A: Given:ρ=1.3 kg/m3μair=1.1*10-5 PaL=2.2 mB=1.2 mFs=1 N

Q: In the mechanism shown in Pigure the link CD rotates at a constant speed of 300 rpm clockwise…

A:

Q: A mobile crane is lifting a large concrete block W at a constuction site, as shown in the figure…

A: To findIf the block weight W = 3400 lb, find the combined reactions at both rear tires(A) and both…

Q: Kindly solve it completely by hand if possible.

A: Step 1: Calculate the mid-point of each molecular weight range First, we will find the mid-point of…

Q: For an OTTO cycle, pressure and temperature at beginning of compression are 100kPa and 25°C, peak…

A:

Q: Suppose parts are to be fitted together as shown below. Dimensions and tolerances (in inches) are in…

A: Given: The dimension with tolerances are d=1.750±0.003, a=0.150±0.006, c=1.400±0.001. The dimension…

Q: Steam is supplied, at 40 bar and specific entropy of 6.0696 kJ/kg-K, to a turbine, condenser…

A:

Q: Ratio of solidification time

A: Given data,  Ratio of solidification time  of a cylindrical casting,where,  height=radiusCubic…

Q: ketch the process on a T-s diagram. Hint: Friction is the only potential source of irreversibilities…

A: To determine the velocity at the exit of the diffusergiven at inlet conditionspressure temperature…

Q: Consider the perpendicular rectangles shown schematically. Determine the shape factor Fs2, F1z and…

A:

Q: Please consider a power producing device that was taking in steam at the 5. rate of 2.1 kg/sec and…

A:

Q: A vacuum cleaner creates a pressure drop Ap across its fan. Relate this pressure drop to the…

A:

Q: When the pole OA is in the position shown, the tension in cable AB is 7.8 kN. (a) Write the tension…

A:

Q: A shaft in equilibrium is shown below with dimensions as given in the table below: a b da dB dshaft…

A: Given data:

Q: A biomass digester receives 23 kJ of energy in the form of heat. There is a mechanical mixer that…

A:

Q: supply as shown in A 5-cm galvanized steel Pipe the figure below. The pipe is 20 m long and has two…

A: To obtain the exit velocity of the water from the pipe outlet, we must apply the Bernoulli's…

Q: An open-top container 0.4 m in diameter is filled with water. Near the bottom of the container,…

A:

Q: Find components of reaction at A (use journal bearing reaction for point A reactions) and also Find…

A:

Q: The crankshaft of a machine runs, on average, at 2280 revolutions per minute for the duration of 2…

A: Given data:- Speed of the crankshaft (N)=2280 rpm Time of operation per day =2 hours Fatigue…

Q: 3.32. How far below the water surface should a vertical square, 1.22 m on a side with two sides…

A:

Q: uestion - YOur objective is to design a vibration absorber (k2,m2) for the following stem. The…

A: the allowable clearance for the absorber motion =0.01 m20 N amplitude =10 rad/s asiming you can…

Q: Air and refrigerant R22 pass through a heat exchanger in two separate streams. Assume no heat…

A:

Q: A rigid, well-insulated tank contains a two-phase mixture of ammonia with 0.0025 ft3 of saturated…

A:

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A: The power transmitted by gear B, P1 = 25 hpThe number of teeth on gear B, Z1 = 24The diametral pitch…

Q: The truss shown in the figure below is made of three A-36 steel members (E=200 GPa), each having a…

A: Given:

Q: A container of weight W = 320 lb is supported by a continuous cable BAC and a small pulley at A, as…

A: The weight is The length dimension are The total length of cable is

Q: A gun is so designed that, on firing, the barrel recoils against a spring. A dashpot, at the end of…

A: