PROBLEM 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d, = 30 mm and d, = 50 mm, find the average normal stress in the mid section of (a) rod AB, and (b) rod BC. [Ans. (a) 84.9 MPa (b) -96.8 MPa] d, di 125 kN В C A 60 kN 125 kN 0.9 m 1.2 m Fig. P1.1 and P1.2

Q: Problem 2. Two rods connected at B are restrained at points A and C. The section AB is steel and Es…

A:

Q: 3. A steel wire with a square cross-sectional area (one of its side is 3mm) is used to support a…

A:

Q: 3. A column is made of concrete having a density of 3000 Kg/m³. At its top B it is subjected to an…

A: Given Data:The density of the material is The load applied to the column is P = 25 kN.The radius of…

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: Two cylindrical cross-section rods AB and BC, which are fixed to the wall and welded together at…

A:

Q: A steel shaft of diameter 50 mm and length 1.2 m (E = 210 GPa and v = 0.3) is loaded with multiple…

A:

Q: A polystyrene rod consisting of two cylindrical portions AB and BC is restrained at both ends and…

A: Given data as per question The diameter of bar AB =1.25 in The diameter of bar BC =2 in  E = 0.45 X…

Q: PROBLEM 2.2 A 1.5 m long steel wire of 6 mm diameter steel wire is subjected to a 3.4 kN tensile…

A: Answer: (a) The elongation in the wire is 0.902 mm. (b) The corresponding normal stress in the wire…

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: b. A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: Given Data

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: 2.13 A steel plate, which is 1.5 m by 1.5 m and 30 mm thick, is lifted by four cables attached to…

A:

Q: 13 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A:

Q: An annular washer distributes the load P applied to a steel rod to a timber support. The rod's…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.