Problem 1. Find the lift force (F) needed to open the arc gate. The diameter of the arc gate is 9m, the width of the gate is 10m, the total weight of the gate and the supporting truss is 117.6X10³N. The horizontal distance between the center F 9m 10m A 7m 1176x10³N 0 of gravity of the gate and the truss and point O (the center of gate hinge) is 7m. The center of the arc is point A. Neglecting all friction.

Problem 1. Find the lift force (F) needed to open the arc gate. The diameter of the arc gate is 9m, the width of the gate is 10m, the total weight of the gate and the supporting truss is 117.6X10³N. The horizontal distance between the center F 9m 10m A 7m 1176x10³N 0 of gravity of the gate and the truss and point O (the center of gate hinge) is 7m. The center of the arc is point A. Neglecting all friction.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
A two-dimensional truss is subjected to horizontal load 10 kN and vertical load 5 kN at Fand Drespectively as shown in figure below. The force in the member DFIS kN. 5 KN 4 m D 2 m 2 m 10KN 4 m
10 m to 15 m M 2. A 200-kg mass Mis attached to a pin at C as shown. Determine the forces acting in the members AC and BC.
A pin-jointed 2-D truss is loaded with a vertical load of 10 kN as shown in figure. The crosssectional area of the horizontal member is 150 mm² and cross-section areas of the members AC and BC are 200 mm² each. Modulus of elasticity of the truss material is 200 kN/mm². The magnitude of horizontal displacement (in mm, round off to two decimal places) of joint Cis A -6m 10 KN 5 m 4.5 m
Determine the axial bar forces of the externally indeterminate truss shown .AE is constant.
9. A single horizontal force P of magnitude 900N is applied to end D of lever ABD shown in the figure below. Knowing that portion AB of the lever has a diameter 36mm, determine a) the normal and shearing stresses on an element located at point H and having sides parallel to the x and y axes, b) the principal planes and the principal stresses at point H. 300 mm 120 mm y B H A 540 mm 36 mm P D
Determine the force in member JH and BH for the truss loaded and supported as shown in figure (3). Does the statically indeterminacy of the supports affect your calculation? Why? 4 m 4 m G 4 m F 4 m A 4 m B 4 m C 4 m 60° E (50+b) kN Fig.3. Q3
Determine the forces in all members of the truss shown in figure. Assume all members are pin connected.
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m -P B 3.5m7 Find the location x of the largest additional vertical force that can be applied to the bar. meters in 2 decimal places
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.
The trussed beam shown is 5.40 m long. A man of weight W is standing at the middle of the beam. Neglect the weight of the beam. strut rod 0.90 m 2.70 m 2.70 m 15. If the capacity of the rod is 2 kN, what is the safe maximum weight of the man? a. 132 kg 16. If the man weighs 85 kg, what is the tension in b. 129 с. 156 d. 187 the rod? a. 1012.40 N b. 1127.05 17. What is the total length of the rod b. 5.69 c. 1403.50 d.1317.90 a. 6.12 m C. 5.34 d. 7.32
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa