Problem 1: The The uniform 30-kg ventilation door OAP is opened by the mechanism shown. Plot the required force in the cylinder DE as a function of the door opening angle over the range 0ses emax where 8max is the maximum opening. Determine the minimum and maximum values of this force and the angles at which these extremes occur. Note that the cylinder is not horizontal when e = 0.

Q: One of the smooth vertical walls supporting end B of the 100-kg uniform shaft is turned through a…

A:

Q: Which method of tolerancing does not exist?   a)Limit tolerance b)Triolateral tolerance c)Bilateral…

A: There are basically three types of tolerances exist in the metrology  Limit tolerance Bilateral…

Q: NPV calculation simulating 20% increase in product cost.

A: PLEASE PROVIDE ME WITH THE QUESTIONS OR A RELEVANT REFERRENCE THAT WILL GUIDE ME  IN HELPING YOU…

Q: The cross-sectional area of the figure below is 0.5 in2. If E = 13 x 106 psi, calculate the total…

A:

Q: Determine the unknown forces by applying d’alemberts principle to a free body.

A: Even in the course of Fundamentals of Dynamics and Kinematics of machines, this principle helps in…

Q: The truss shown is used to support a 11 kg block with a pin at A and a roller at E. Given a = 1.1 m,…

A: To find the internal forces in members AB, BD, BC, and CD of the truss, we can analyze the forces…

Q: m The hoist supports an engine Determine magnitude of the force created by the engine mass

A: tanθ1=a+ba-btanθ1=2.2+1.12.2-1.1θ1=71.56o∑Fv=0RA+RB-mg=0RA+RB=mgRA+RB=175×9.81RA+RB=1716.75 N ,…

Q: 7.5' |A 6.8' 0.6' B 2.4' 3.6' OFF HIO

A:

Q: PROBLEM 1: Consider the truss system to the right. All members are two force members. There is a pin…

A:

Q: A uniform bar with mass M = 3.25 kilograms is shown in the diagram. hlo required to keep the

A:

Q: ROBLEM 1: insider the truss system to the right. All embers are two force members. There is pin at…

A: To find out :-Forces in each member.

Q: Consider the following system in static equilibrium. Force vector Facts at a distance" from the pin…

A: (a) Draw the free-body diagram of bar.

Q: A beam with a length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a…

A: Given: The length of the beam is, l=2 m The mass os the beam is, W=10 kg×9.81 ms2=98.1 N The mass…

Q: A. Draw a different configuration, and make it a diagram similar to Fig. 3. Specify each mass and…

A:

Q: The 50-kg homogeneous smooth sphere rests on the 30° incline A and bears against the smooth vertical…

A: As per given question  Weight =50kg Angel=30° We have to determine contect of force A and B

Q: Using the method of joints, calculate the force in each member of the truss shown. State whether…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: draw the free-body diagrams for the set (or structure) complete and each of its parts. Ignore…

A: (a) Free-body diagram of the complete structure is given as, At points A and B, the hinge joints…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.