Problem (1): The rigid, horizontal slab is attached to two identical copper rods. There is a gap A 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85°C. Use the following data: A (mm?) a (FC) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10-6 70 Copper Aluminum

Problem (1): The rigid, horizontal slab is attached to two identical copper rods. There is a gap A 0.18 mm between the middle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 85°C. Use the following data: A (mm?) a (FC) E (GPa) Each copper rod 500 16.8 x 10-6 120 Aluminum rod 400 23.1 x 10-6 70 Copper Aluminum

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) A composite bar is shown in figure Qlb. Determine. The thermal stresses in copper tube and steel bar i. ii. Reaction in the steel bar. Copper tube (a1, E1) Steel bar (a2, E2) L = 500mm Fig Qlb Given: di = 100mm, L = 500mm d2 = 200mm, AT = 100°C Соррer Steel E (GPa) 100 200 al°C 16х 10-6 12 x 10-6
2. With an area of 420 mm², a bronze bar that is 3 m long is placed between two rigid walls as shown in Fig. below. Find the temperature at which the compressive stress in the bar will be 55 MPa, if at a temperature of -20°C, the gap A = 3 mm. Use a = 18.0 x 10“ m/(m:°C) and E = 80 GPa. L = 3 m
ANSWER WITH CLEAN SOLUTIONS AND WITH FREE BODY DIAGRAM
Solve the problem, involving Strength of materials
A composite section 2 m in length, consisting of a steel tube with outer diameter 24 mm and thickness 3 mm, encloses a solid copper bar 18 mm diameter. An axial compressive load of 250 KN is applied on the assembly. Young’s modulus for steel and copper are taken as 2 x 105 N/mm2and 1 x 105N/mm2respectively. Calculate the stresses developed in steel and copper. Also calculate the load taken by both the materials.
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulusE=120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD AND show me your step Please make sure your answer is correct please
Please answer soon I will rate positive
0.6 m 1.2 m 3.1 The rigid bar af negligible weight is supported as shown in the figure. If W= 80 kN, compute the temperature change of the assembly that will cause a ten- sile stress of 50 MPa in the steel rod. Use the following data: Bronze 3 m Steel 5 m A (mm) a (1°C) E (GPa) H10m Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83
SHOW ILLUSTRATION AND SOLUTION Problem 2: Steel railroad rails 10 m long are laid with a clearance of 3 mm at atemperature of 15 oC. E = 200 GPa and  = 11.7 x 10 - 6/oC. 1. At what temperature will the rails just touch?2. What stress would be induced in the rails at that temperature if there were no initial clearance?
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Don't waste my question please, I need the solution don't just capy the answer that I give there.