Problem 1: The 8-lb rod AB is attached to a collar of negligible weight at A and to a flywheel at B. The flywheel has a weight of 32 lb and a radius of gyration of 9 in. Knowing that in the position shown the angular velocity of the flywheel is 60 rpm clockwise, determine the velocity of the flywheel when point B is directly below C. 36 in. B 12 in. OA

Problem 1: The 8-lb rod AB is attached to a collar of negligible weight at A and to a flywheel at B. The flywheel has a weight of 32 lb and a radius of gyration of 9 in. Knowing that in the position shown the angular velocity of the flywheel is 60 rpm clockwise, determine the velocity of the flywheel when point B is directly below C. 36 in. B 12 in. OA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2. Two uniform disks of the same material are attached to a shaft as shown. Disk A has a weight of 10 lb and a radius r = 6 in. Disk B is twice as thick as disk A. Knowing that a couple M of magnitude 22 lb. ft is applied to disk A when the system is at rest, determine the radius nr of disk B if the angular velocity of the system is to be 480 rpm after 5 revolutions. A M b B 2b
The circular platform A is fitted with a rim of 200-mm inner radius and can rotate freely about the vertical shaft. It is known that the platform-rim unit has a mass of 5 kg and a radius of gyration of 175 mm with respect to the shaft. At a time when the platform is rotating with an angular velocity of 50 rpm, a 3-kg disk B of radius 80 mm is placed on the platform with no velocity. Knowing that disk B then slides until it comes to rest relative to the platform against the rim, determine the final angular velocity of the platform.
A 3 cylinder single acting engine has its cranks set equally at 120° and it runs at 600 rpm. The Torque crank angle diagram for each cylinder is a triangle for the power with maximum torque 80 N-m at 60° after dead centre of the corresponding crank. The torque on the return stroke is sensibly zero. Determine the (a) Power developed (b) K if the flywheel used has a mass of 10 Kg. and radius of gyration is 8 cm (c) Coefficient of luctuation of energy (d) Maximum angle of the flywheel CYLI CYL2 CYL3 80 MMT 60 120 I 8O 240 300 360
Problem No. 5 A rotating shaft carries four masses A, B, C and D rigidly attached to it; the centers of mass are at 30 mm, 36 mm, 39 mm and 33 mm respectively from the axis of rotation. The masses are 7.5 kg, mB, 5 kg and 4 kg respectively. The axial distance between A and B is 0.4 m, that between B and C is 0.5 m and the axial distance between C and D is H meters. The eccentricities of A and C are at 90° to one another. If the shaft is to be balanced completely, find mB, H and the angular positions of the masses B and D.
A uniform 144-lb cube is attached to a uniform 136-lb circular shaft as shown, and a couple M with a constant magnitude is applied to the shaft when the system is at rest. Knowing that r = 4 in., L= 12 in., and the angular velocity of the system is 960 rpm after 4 s, determine the magnitude of the couple M.
Dynamic Problem, reply as soon as posible. The double pulley system weighs 30 lbs. and has a 6.5-inch center radius of gyration. Cylinders A and B areconnected to the double pulley by cords that wrap around the circles whose radii are shown. Thecoefficient of kinetic friction between block B and the surface is 0.25. If the system is released from rest atposition shown, determine:A) The velocity of cylinder A just before hitting the ground.B) The total distance cylinder B travels before coming to rest.
A 6-lb homogeneous disk of radius 3 in. spins as shown at the constant rate w1 = 60 rad/s. The disk is supported by the fork-ended rod AB , which is welded to the vertical shaft CBD The system is at rest when a couple M0 is applied as shown to the shaft for 3 s and then removed. Knowing that the maximum angular velocity reached by the shaft is 18 rad/s, determine (a) the couple M0) the dynamic reactions at C and D after the couple has been removed.
A 197-kg flywheel is at rest when a constant 300 N·m couple is applied. After executing 560 revolutions, the flywheel reaches its rated speed of 2400 rpm. Knowing that the radius of gyration of the flywheel is 400 mm, determine the average magnitude of the couple due to kinetic friction in the bearing. N.m. The average magnitude of the couple due to kinetic friction in the bearing is [
A stationary horizontal plate is attached to the ceiling by means ofa fixed vertical tube. A wheel of radius aa and mass mm is mounted on a light axle ACAC that is attached by means of a clevis at AA to a rod ABAB fitted inside the vertical tube. The rod ABAB is made to rotate with a constant angular velocity ΩΩ causing the wheel to roll on the lower face of the stationary plate. Determine the minimum angular velocity ΩΩ for which contact is maintained between the wheel and the plate. Consider the particular cases ( aa ) when the mass of the wheel is concentrated in the rim, (b) when the wheel is equivalent to a thin disk of radius aa also extend the problem using Kinematic and Kinetic analysis
The 100-kg projectile shown has a radius of gyration of 100 mm about its axis of symmetry Gx and a radius of gyration of 250 mm about the transverse axis Gy. Its angular velocity v can be resolved into two components; one component, directed along Gx, measures the rate of spin of the projectile, while the other component, directed along GD, measures its rate of precession. Knowing that θ= 6° and that the angular momentum of the projectile about its mass center G is determine (a) the rate of spin, (b) ) the rate of precession.
Only need A, B, and C please.
An experimental Fresnel-lens solar-energy concentrator can rotate about the horizontal axis AB that passes through its mass center G. It is supported at A and B by a steel framework that can rotate about the vertical y axis. The concentrator has a mass of 30 Mg, a radius of gyration of 12 m about its axis of symmetry CD, and a radius of gyration of 10 m about any transverse axis through G. Knowing that the angular velocities w1 and w2 have constant magnitudes equal to 0.20 rad/s and 0.25 rad/s, respectively, determine for the position 0= 60° (a) the forces exerted on the concentrator at A and B, (b)the couple M2k applied to the concentrator at that instant.