PROBLEM 1 Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube Wall thickness-2mm ABC is a sector with a radius of 50 mm c. Shear flow d. Shear stress AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium e. Angle of twist A 90 T B. D 3R

PROBLEM 1 Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area b. Perimeter of the thin walled tube Wall thickness-2mm ABC is a sector with a radius of 50 mm c. Shear flow d. Shear stress AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium e. Angle of twist A 90 T B. D 3R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A thick cylinder of inner dia D, wall thickness t, and length L is sealed at its both ends with caps. The thickness of the cap is t,. Allowable tensile yield stress = o, and allowable shear stress = t A gas is pumped into this cylinder at pressure p. = 0, y %3D саp will yield in shear at circumference of diameter The сap D when the gas pressure applied is more than ty 3D Pr P
40 mm 10 mm 40 mm An aluminum tube with the cross section shown has a constant wall thickness 2 mm. A torque T= 400 N-m is applied to the tube. Use G= 28 GPa * What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object' The shearing stress value will be The angle of twist result is 20 mm
Please Do not copy.
H.W: Design a cast iron rigid type flange coupling to transmit 20 kW at 900 r.p.m. from an electric motor to a compressor. The following permissible stresses may be used: Shear stress for shaft, bolt and key material =40 MPa Crushing stress for bolt and key = 80 MPa %3D Shear stress for cast iron =8 MPa Draw a neat sketch of the coupling.
Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is subjected to an internal pressure of 7 MN/m²; the increase in volume due to the pressure is 2.36 x 106 m³. Find the values of Poisson's ratio and the modulus of rigidity. If, in addition to the internal pressure, the cylinder is subjected to a torque of 190 N.m, and axial tensile force at the ends of 650 N, determine the magnitude of the principal stresses set up in the cylinder and their directions. Assume the Elasticity modulus, E = 210 GN/m².
The 100 mm diameter steel bar is bored to 50 mm diameter over half its length as shown in Figure Q2. Under an axially applied torque, T the depth of plastic penetration in the hollow shaft section is 20 mm. The shear yield stress of the tube material is given as 280 MPa. a) Find the magnitude of torque applied to the shaft b) Show the state of condition (elastic, partial plasticity or fully plastic) in the solid shaft c) Calculate the depth of plastic penetration in the solid shaft, if any d) Sketch the shearing stress distribution in the solid and hollow shafts 100 mm 50 mm Figure Q2
A 120 mm ×100 mm ×20 mm T section is used as a simply supported beam. The beam carries the applied eccentric load F of 120 KN at the position indicated in the Figure Q5. Start your calculations be setting an origin from the right most point on the cross section and determine the following : 5.1.The maximum compressive and tensile longitudinal direct stresses induced in the column. 5.2. Plot the stress distribution diagram and determine the position of the NA
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
A hollow aluminum tube used is a roof structure has an outside diameter d2=70mm and inside diameter d1= 50mm. The tube is 2.5m long and the aluminum has a shear modulus of G=28 GPa. a.) If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist in degrees when the max shear stress is 50MPa? b.) What diameter 'd' is required for a solid shaft to resist the same torque with the same maximum stress?
material mechanics
a) A steel 4 X 4X 0.25-inch square tube (moment of inertia I = 8.215 inª) is used as a simply supported beam. A 100-pound weight is dropped from a height of 24 inches onto the beam at mid- span. Find the maximum stress in the beam. Use E = 29 X 106 psi. 8 ft k = 200 lb/in 100 lb 8 ft b) Instead of fixed supports, the beam is supported by springs at both ends. Find the maximum stress in the beam when the 100-pound weight is dropped from a height of 24 inches (same beam properties as in part a). 24 in 100 lb 8 ft 24 in 8 ft k = 200 lb/in
For the figure shown below. Find the maximum allowable value of P if the bending stresses are not exceeding 3.5 KN/m² in tension and 8KN/m² in compression 0.015m 0.015m 2P |4P ЗР 0.2m . 0.25m 0.02m 2m A A 2m.