Problem 1: For a 20-ply lay-up [(0/90)s]s in which ply thickness is 0.1 mm and stiffness is: 20. 0.7 0 [Q]= 0.7 2.0 0 0 GPa 0 0.7 find the residual stresses if the cure temperature is 225°C, and the service temperature is 25°C. Given a₁= 0.02 x 10-6 C-1 and a2-22.5 x 10-6 *C-1

Problem 1: For a 20-ply lay-up [(0/90)s]s in which ply thickness is 0.1 mm and stiffness is: 20. 0.7 0 [Q]= 0.7 2.0 0 0 GPa 0 0.7 find the residual stresses if the cure temperature is 225°C, and the service temperature is 25°C. Given a₁= 0.02 x 10-6 C-1 and a2-22.5 x 10-6 *C-1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A disk of SBR elastomer 3.0 cm in diameter 0.5 cmthick is used as a cushioning surface between two steel rods ofthe same diameter, as shown below (not to scale). a. If the rods are brought together with an axial force of 100 N such that the SBR is compressed elastically between them, what is the thickness of the SBR under load? b. Under the same conditions as part (a), what is the greatest possible diameter of the SBR under load? c. If the SBR is bonded to the rods, how far can one rod be rotated with respect to the other before the SBR/rod interface fractures? Assume that the rods are essentially rigid and the distance between them remains constant. Please answer in degrees of rotation.
Rigid bar ABCD is supported by a smoth pin at D and by vertical aluminum alloy [E=10,000 ksi] bars attached at joints A and C. Bar (1) was fabricated to its intended length L1=40 in. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2=59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by Δ=0.12 in. After bar (2) has been stretched and connected to the pin at C, a load P=20 kips is applied to the rigid bar at B. Use the following additional properties and dimensions: A1=A2=0.75 in2, a = 36 in, b =54 in, and c = 48 in. Determin: a) The normal stresses in bars (1) and (2). b) The deflection at A of the rigid bar.
M13.6 Principal stresses from rosette data scenes -200 µE 23 Eb = 200 με Ec 500 µE 30° 30° Ex (LE) a Ey (µE) Yxy (Lurad) The strain rosette shown was used to obtain normal strain data at a point on the free surface of a steel (E = 200 GPa; v = 0.32) plate. Op1 (MPa) Determine the normal strains, the shear strain, and the principal stresses in the x-y plane. Op2 (MPa) Try One 1st 2nd 3rd attempt enter
The state of stress at a point in an engine piston is given in the x-y-z coordinates by: 90 180 [0]=0, MPa = 180 240 yx yy 120 zy Using the matrix transformation law, determine the state of stress at the same point for an element rotated about the x-axis (in the y-z plane) 60° clockwise from its original position. Calculate the stress invariants and write the characteristic equation for the original state of stress, Calculate the deviatoric invariants for the original state of stress, Calculate the principal stresses and the absolute maximum shear stress at the point. What are the stress invariants and the characteristic equation for the transformed state of stress, а. b. С. d. e
Derive the following equation for computing shear stress in a solid bar along an oblique plane with angle B with respect to the vertical plane. The bar is subjected to centric axial loading. sin 0 cos 0 T = Ao
Two links are connected by a single pin and a tensile force F is applied. The links and the pin are made from Aluminum(sigma_y = 35ksi and T_y = 20ksi). The dimension of the link is 5 inch high by 0.5 inch thick. Find the optimal diameter for the pin and the maximum force,F that can be applied to the linkage before incuring permanent deformation.
a rectangular stepped bar is shown. the bar is loaded in bending. determine the fatigue stress concentration factor if the ultimate stress of the material is 690 mPa. please inlcude how to calculate the notch sensitivity.
1. A 0.015 meter diameter bar of steel is stress tested and the following stress-strain curve is produced Stress (psix 10 60 50 8 20 10 1 MPa 300 100 psi (x 10%) 50 200-30 OL 40- 20- 10 0.05 0.005 1 L 0.010 0.10 Strain a. What is the ultimate tensile strength (MPa)? d. What is the yield strength(MPa)? 0.15 c. What is the percent plastic elongation at the time of fracture? e. What is the Modulus of Elasticity (GPa)? 400 300 200 Stress (MPa) b. What is the greatest load that can be place on this bar before failure(N)? 100 10 0.20
A solid bar of length L = 4 m and diameter 200 mm is heated from 20 to 320 degrees celsius and restrained between two solid immovable walls. Young's modulus of the material is 90 GPa and the coefficient of thermal expansion is 22 x 10-6/°C. →Calculate the thermal strain, e, in micro-strain correct to two decimal places. micro-strain. Calculate the thermal stress, o, in megapascals (MPa) correct to two decimal places. E: σ: MPa. Hence calculate the force exerted by the bar in meganewtons (MN) correct to two decimal places: F MN. L
Q: In the stretching of round bar has 30 mm origin diameter, it turns out the following UPD=NPD and 6 = 173+109€0.31 MPa. Find: 1. The redundant work for stretching process. 2. The force and diameter at fracture point.
An initially rectangular element of a material is deformed into the shape shown in the figure. Deformed Undeformed 16.6 0.1992 mm 15.7 0.2 mm Normal strain in the x- direction * -4.0 x 10^-3 4.0 x 10^-3 10 x 10^-3 -10 x 10^-3 Normal strain in the y- direction O -4.0 x 10^-3 4.0 x 10^-3 O 10 x 10^-3 O -10 x 10^-3 0.1515 mm 0.15 mm
In the attached picture there is a sketch of a socket wrench. Assume the wrench is held at a fixed point “A”. The yield stress of the material is known to be 500 MPa. Answer the questions below Describe the stresses at point “A” and their causes and calculate the stresses. Determine the factor of safety against yield assuming the Tresca yield criteria. Determine the factor of safety against yield assuming the von Mises yield criteria using both principal stresses and “Cartesian” stresses. Do your values match or not, and is this expected? Explain. Do the calculated values make sense with the respect to the Tresca value? Explain, why or why not?