PROBLEM 1: Determine the Centroid and the Moment of Inertia about the x-y axes of the shaded area in FIGURE 1 FIGURE 1 2m y 4m 5m 2.5m 10m

Q: Q1 A hydraulic proportional-plus-integral- plus-derivative control system is shown in figure, the…

A: A hydraulic Proportional plus integral plus derivative control system   The figure shows a schematic…

Q: 1. A two-stage vapour compression refrigeration system with a direct contact heat exchanger (flash…

A:

Q: Two mole of an ideal manoatomic gas goes from a to c along the diagonal path in the figure below.…

A: Ideal gas equation relates the temperature, volume and pressure of an ideal gas. It is given as…

Q: 1.606 As the hydraulic cylinder rotates around O, the exposed length I of the piston rod P is…

A: To Find :  The magnitude of the velocity and acceleration of end B. Given :  The length is l=125 mm.…

Q: 3. In a 12 tones refrigeration ammonia plant, compression is carried out in two stages with water…

A:

Q: The 0.5-kg ball is fired up the smooth vertical circular track using the spring plunger. The »lunger…

A: To Find : The distance pulled back and released. Given :  The mass of ball is m=0.5 kg The spring…

Q: 2 - Explain the bonding, hybridization and geometry of carbon nanotubes that are used to help store…

A: Introduction: carbon nano tubes are in the form of cyliders. It can be made by the graphine sheet by…

Q: Select all flow visualization techniques for gas flow at 1500m/s at sea level, among them, which can…

A: The skill of making flow patterns visible is known as flow visualization. Because most fluids (air,…

Q: A full journal bearing is required for a 30 mm diameter shaft rotating at 1200 rpm supporting a load…

A:

Q: 4. From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.35°.…

A:

Q: 3. Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A:

Q: The flow of a particular fluid is described by a velocity field given as u = x²y v = x³ = xy² w = 0…

A:

Q: Please give the answer as in the format asked

A:

Q: FIGURE 1 60 kN B 0.75 E F :1.00 1.00. 1.00 25 kN

A:

Q: A refrigeration plant comprises three evaporators of capacities 10 tonnes at 10°C, 20 tonnes at 5°C…

A:

Q: A hot gas at 300°C with convective heat transfer coefficient of 100 W/m²-K is flowing through an…

A: Given:Hot gas temperature, Tg=300oCConvective heat transfer coefficient of hot gas, hg=100…

Q: 5. A 45 tonnes capacity compound NH, compression system with water intercooler after low pressure…

A:

Q: A spring with a mass of 1 kg has a spring constant 43 kg/s2. If the spring begins at equilibrium…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A: Consider the U-tube manometer according to the given queston as shown below, The manometer is…

Q: 02/A system for controlling flow is shown in figure. The increásing in the desired flow setting…

A: The overall block diagram representation of the given system can be drawn as follows:

Q: 6. An ammonia refrigeration system operates in a simple saturation vapour compression cyde to…

A:

Q: A A billboard BF weighing 4KN is subjected to a wind pressure of 5kN/m as shown in the figure.…

A: Given:The weight of the beam BC is the uniformly distributed load of beam BC is the  horizontal…

Q: 2. A furnace wall is made up of three layer of thickness 250 mm, 100 mm, and 150 mm with thermal…

A:

Q: 2. An eccentric Cam, too mmin diameter otates with an eccentricity of lommas hown in the figurę. The…

A: Given: Pmax=350 N; Pmin=100 Ne=10mmspring index C=6

Q: 1. Given the data as shown in the figure, determine the (a) maximum torque Tmax (N-mm) that maybe…

A:

Q: A thin uniform conducting disc of radius r and mass m rests on a horizontal tabletop where a uniform…

A: Given Data;- Radius = r Mass =m Uniform magnetic field of induction = B Co-efficient =μ Angle =θ…

Q: 4. Calculate the power required to compress 18 kg/min of NH, from saturated vapour at 1.4 bar to…

A:

Q: using the curved-beam theory thesPr.ny bending stresses are givenby Prove that Gb=K; (6Fir for 93…

A: given; bending stress (σb)=k.M.yIprove that  (σb)=k.6F.ra3 dimension of square cross section=a

Q: In free space, a particle is projected from a point P on axis of a fixed rigid cone AOB, at an angle…

A: Velocity is the forward motion of a body. It is equal to the distance covered by the body per unit…

Q: It is required to design a helical torsion Por a window - shode. The spring is made of patented…

A:

Q: Kindly please answer in a table form

A:

Q: The following data refer to a two-stage vapour compression system: Condensing temperature = 40°C…

A:

Q: 4m R RKBO MICS O CLE 1.602 The cable connecting the winch A to point B on the railroad car is wound…

A:

Q: m. Neglect friction.

A: The force equilibrium condition-

Q: An ammonia refrigerator produces 20 tonnes of ice per day at 0°C. The condensation and .2…

A: Given: The refrigerator produces 20 tonne ice per day. Fusion of ice→hfg=335 KJ/Kg And one tonne=907…

Q: of length lo = 5.0 m and stiffness k= 50 N/m is inside 13. A ight a fixed box with a small portion…

A: The initial length of the chord, lo = 5.0 m The stiffness of the chord, k = 50 N/m The length of the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.