Problem 1 • A sinusoidal current of 10Arms at a 60Hz fundamental frequency is contaminated with a ninth harmonic current. The current can be expressed as i(t) = 10v2 cos(2n60t) + 1,vZ cos(18760t) Amps Determine the value of the 9th harmonic RMS current l9, the power factor, and the distortion factor for each of the following cases of THD (a) 5% (b) 10% (c) 20%

Problem 1 • A sinusoidal current of 10Arms at a 60Hz fundamental frequency is contaminated with a ninth harmonic current. The current can be expressed as i(t) = 10v2 cos(2n60t) + 1,vZ cos(18760t) Amps Determine the value of the 9th harmonic RMS current l9, the power factor, and the distortion factor for each of the following cases of THD (a) 5% (b) 10% (c) 20%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Consider a sinusoidal signal x(t)=sin(2n50t) for ten complete cycles. Using this signal, plot to represent the following: (a) Plot x(t) as analog continuous signal (b) Plot x(t) as analog discrete-time signal (c) Quantize the signal to 4 levels, +1, +1/3, -1/3, -1 and plot the corresponding i) digital discrete-time signal; and ii) digital continuous signal (d) Plot the amplitude spectrum for the sinusoidal signal generated in part (a). (e) Plot the phase spectrum for the sinusoidal signal generated in part (a).
During a lab session, the lab instructor presented the class with an alternating voltage which has a value of v=50 Sin 800t. With this material; each student was given the appropriate equipment to show that the values of the following parameters can be measured by an analyzer. Compile the correct results of the analyzer.i. The Amplitude valueii. The Frequencyiii. The Average valueiv. The RMS valuev. The Form Factorvi. The Peak Factorvii. The Instantaneous voltage when t =3 ms?
c) A Flyback converter has an input of 332 V from a DC source, operating at 40 kHz with duty cycle approximately 1/2. The rated output is 12 V at 5 A. The circuit operates with continuous inductor current at threshold 1.5 A, and the turn ratio must be an integer. By assuming that all the components are ideal, and capacitor and inductor are operating in steady state: i. Draw the converter circuit. ii. Determine the inductor's turn ratio. iii. Determine the primary inductance. Sketch the diode current and switch current. iv V. Find the peak and mean of the switch current.
An impedance of 100 - j50 ohms in a network operating at 50 Hz represents a) A resistor of 100 ohms and an inductor of 0.159 Henrys b) A resistor of 100 ohms and a capacitor of 63.66 microfarads c) A 100 ohm resistor and a 1 Henry inductor d) A 100 ohm resistor and a 400 microfarad capacitor e) None of the above
3 Find the average value of the output voltage for the circuit of Figure P9.33 if the input voltage is sinusoidal with an amplitude of 5 V. Let V, = 0.7 V. %3D 100 nF Vin Vout
Hononta (Vj Ais M QUESTION (1) pressure signal from a force transducer is given as under. Analyze it in terms of harmonics, amplitude, circular frequency, cyclic frequency, time period and phase. A. P=15 sin(20m + +12 sin(40t-)+10sin(60t +)+8sin(100zt +")+5sin(140nt -"). +3sin(180) Pa %3D
2. Write an OCTAVE program to plot the signal given below P=Pmax Sin(2πft); where Pmax=10 MW, f=60 Hz Find out time.peniod and verify it with graph. Assume necessary data.
In a 220 Vrms, 60 Hz. Source, determine the following values:
The pulse voltage waveform displayed on a CRO, is shown in figure given below. Find, (a) Frequency. (b) Magnitude of the pulse. (c) The amplitude. 21 0.5 5 0.2 10 20-(Vicm 5 ms 100 us 50 ms time/om 500 ms 30- 40 50 2s
92.54W A three phase full controlled converter is supplied by a phase voltage Vg=D120V, 60 Hz. Consider a resistive load R=10 Q. If the RMS value of the output current is equal to 10.94A and the input Volt Ampere VA = 3125VA, then the output power P. and the power factor would be equal to: Select one: O a. 1196.84W, 0.772 lagging O b. 3196.84W, 0.772 lagging Oc. 1196.84W, 0.382 lagging O d. 3196.84W, 0.382 lagging A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: Vcc = 200 V V -5 V Ie - 10 A Vera -2V L-- – 120 A t. -05us t - 1 us t. A us t. - 3us and f -10 TOSHIBA
9. PLOT. Plot the sine wave at frequency fm and the sampling signal at frequency fs1. Write a MATLAB program to take input both fm and fs1 and plot the curves mentioned above.,.
QI-A) A sinusoidal vohage v,(t) = 20 sin wtis passed through half waverectifier. Find 1) The period T. 2) The DC value of output voltage o- 3) The first harmonics of output voltage in.