Problem 1-A 6 V battery with storage capacity of 2 A-hr and internal resistance of 12 is connected to a 19 2 load resistor for 30 minutes as shown in the diagram. 10 a) How much total energy is stored in the battery before it is connected to the load? b) What average power is dissipated in the load while connected? c) How much total energy was dissipated in the load in 30 minutes? d) How much energy remains in the battery at the end of the 30 minutes? 6 V 19 Q

Problem 1-A 6 V battery with storage capacity of 2 A-hr and internal resistance of 12 is connected to a 19 2 load resistor for 30 minutes as shown in the diagram. 10 a) How much total energy is stored in the battery before it is connected to the load? b) What average power is dissipated in the load while connected? c) How much total energy was dissipated in the load in 30 minutes? d) How much energy remains in the battery at the end of the 30 minutes? 6 V 19 Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Solve the problem by hands to show all steps
CIRCIUTS
Solve again for the following: a. total resistance b. current passing through the resistor (10 ohms) c. current passing from point b to point a d. voltage across the resistor (20 ohms)
2. In Figure, the battery voltage is V 65 velts, and the values of the resistances, in ohms, are 38, 17, and 27, as shown. Find: Total resistance seen by the battery, (b) Current measured by the ammeters shown in the figure, V-65 V 17Q 27Q
In the circuit in figure, the emf from the battery is equal to 30 V, L= 5H, R1 = 10 ohms and R2 = 20 ohms. Calculate how much time has to pass after closing the switch K for the current in the resistors to be the same. R, D
Questions 1-4 are based on the SLI battery (one battery module) in a car with specifications: Open Circuit Voltage (OCV): 12 V Resistance: 0.01 ohmDischarge Capacity: 50 Ah You are building an electric go-cart battery pack using 4 of these battery modules connected in series. 1. What is this battery pack open circuit voltage? 2. What is this battery pack capacity? 3. What is this battery pack energy? 4. Now connecting this battery pack with a traction motor, what is the battery pack voltage if the motor draws 200 A? Hint: Need to consider the battery internal resistances (in series connection) because now there is a load (not OCV).
Find value of current. I need it in 30 minutes. Please.
electrotechnical and electrical machinery
5. Consider the resistor network connecting points A and B in the figure be- low. What is the equivalent resistance between points A and B? If the potential difference between A and B is 12 volts, what is the current in the 4 2 resistor? What is the rate at which heat is produced in the 42 resistor? 1 12n
For the DC circuit shown in the accompanying figure, find the voltage across each resistor and the current through each resistor.
Determine the equivalent resistance across the terminal
Theory The defining characteristic of a series circuit is that there is only one path for electrons to flow. The principle to understand is that the amount of current is the same through any component in the circuit. This is because there is only one path for electrons to flow in a series circuit. Circuit Diagram R1 R2 R3 10 k 5 k 2.2 k VI 10 V Procedure 1. Check the resistor using the multi-meter and make sure the values are correct. 2. Set up the circuit on the connection board as per the circuit diagram. 3. Connect the Power supply to the circuit. 4. Adjust the voltage of the power supply as per the circuit diagram. 5. Measure the Voltage and current needed as per the tabular column Observations Sr. No I V 1. Results For the given supply voltage, calculate the value of current (I).