Testing a Battery Without a TesterThe internal resistance says a lot about the state of thebattery.To calculate the actual internal resistance of the battery,MULTIMETERproceed as follows:• Measure the source voltage (voltage when no current isflowing) (Vo) and terminal voltage (voltage when currentis flowing) (Vc).CE CAT ICalculate the voltage drop across the internal resistanceOFFV 200m20M(V, - Vo- Vc).CURRENT CLAMP2.2M• Measure the load current (1).Calculate the internal resistance (R = V/ I).OFF20--200K1mV/A200-20K10mV/A6002K...AZERO1020010 COMThe battery being tested has a CCA rating of 640 A.The battery manufacturer specifies that the maximuminternal resistance should not exceed 2.5 + cold crankingamps (CCA) rating of the battery.What is the maximum acceptable internal resistance valuefor this battery?

CCA rating of battery is 640A (given). And maximum allowable internal resistance of battery is…

Tésting à Băttèry Without a Tester The internal resistance says a lot about the state of the battery. To calculate the actual internal resistance of the battery, MULTIMETER proceed as follows: 00 • Measure the source voltage (voltage when no current is flowing) (Vo) and terminal voltage (voltage when current is flowing) (Vc). CE CATI OFF • Calculate the voltage drop across the internal resistance V 200m 20M (V = Vo-Vc). CURRENT CLANMP 2. 2M Measure the load current (1). • Calculate the internal resistance (R = V/). OFF 20- -200K 1mV/A 200- 20K 10mV/A 600 2K A ZERO 10 200 The battery being tested has a CCA rating of 640 A. The battery manufacturer specifies that the maximum internal resistance should not exceed 2.5 cold cranking amps (CCA) rating of the battery. A 1 COM What is the maximum acceptable internal resistance value for this battery?

Tésting à Băttèry Without a Tester The internal resistance says a lot about the state of the battery. To calculate the actual internal resistance of the battery, MULTIMETER proceed as follows: 00 • Measure the source voltage (voltage when no current is flowing) (Vo) and terminal voltage (voltage when current is flowing) (Vc). CE CATI OFF • Calculate the voltage drop across the internal resistance V 200m 20M (V = Vo-Vc). CURRENT CLANMP 2. 2M Measure the load current (1). • Calculate the internal resistance (R = V/). OFF 20- -200K 1mV/A 200- 20K 10mV/A 600 2K A ZERO 10 200 The battery being tested has a CCA rating of 640 A. The battery manufacturer specifies that the maximum internal resistance should not exceed 2.5 cold cranking amps (CCA) rating of the battery. A 1 COM What is the maximum acceptable internal resistance value for this battery?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the network shown in Figure B22 , assume E = 12V, Diode Di as silicon and D2 Germanium, R1=1.5KN and R2=1KQ. Calculate, i. Current I1, ii. Current Ip2, iii. Voltage across resistor R2 R1 D1 E D2 Ip2 I2 R2 Figure B22
vs=10v find vz and iz
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through. A.Insulator B.Conductor C.Semiconductor
Make sure to indicate everything which needs to be indicated for an upvote. Thank you.
i. Draw a circuit diagram of potentiometer method with naming the components and derived the ratio of the two potentiometer readings. ii. In a measurement of resistance by potentiometer, the voltage drops across resistor under test and across 0.0252 standard resistors were found to be 0.882V and 1.2 V respectively. Determine the value of under test. iii. Write two advantages and disadvantages in Potentiometer method.
In * semiconductor, the concentration of the holes and electrons is equal.
Please answer only handwritten solution please And in short please
Draw VI characteristics of solar PV cell.
For the diode circuit of the figure below: 1. Determine v, and sketch its waveform for at least 4 cycles 2. Determine the average (dc) voltage established the load Show the details of your work. Without a complete solution (step-by-step solution) will invalidate your answer. 120 V 2.7 kN -120 V
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm
4. Find the current through the diode in the circuit. Assume that the diode is ideal. V2= W Volts R1 X K Ohms R2= Y K Ohms + V2 mu R1 ww R2 D3