Pp= 400k P, = 500k Pp= 400k P = 500k A steel column with the bottom end fixed and the top end pinned carries a service axial dead load of 400k and live load 13 ft of 500k. The column has a span length of 30 ft. On the weak axis, a pin support is added at a distance 13 ft from the pinned end at the top to strengthen the weak axis. 30 ft 17 ft Po= 400k P = 500k PD= 400k P = 500k Select the lightest W14 section for this column to carry the applied loads Strong Axis Weak Axis

Pp= 400k P, = 500k Pp= 400k P = 500k A steel column with the bottom end fixed and the top end pinned carries a service axial dead load of 400k and live load 13 ft of 500k. The column has a span length of 30 ft. On the weak axis, a pin support is added at a distance 13 ft from the pinned end at the top to strengthen the weak axis. 30 ft 17 ft Po= 400k P = 500k PD= 400k P = 500k Select the lightest W14 section for this column to carry the applied loads Strong Axis Weak Axis

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is positive if in tension, negative if in compression. E 13' F 13' G 11' 13' 13' 620 Ib Answer: BG =
F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
A solid brass [E = 109 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each have a diameter of 27 mm and segment (3) has a diameter of 13 mm. Assume L1 = 1.8 m, L2 = 1.0 m, L3 = 1.7 m, R = 38 kN, Q = 14 kN, and P = 24 kN. Determine:(a) Determine the axial force in section (2) in kN. (b) Determine the deflection of joint D (positive if downward) with respect to the fixed support at A. (c) Determine the maximum normal stress in the entire axial member. Give answer in MPa.
namber 22
The single story two-bays frame is unbraced, and bending is about the x axis of each member. All beams are W16 × 57, and all columns are W10 × 100. If L1,beam = 18 ft, L2,beam = 20 ft, Ibeam = 758 in4, Lcolmns = 15 ft and Icolumn = 623 in4 . Assume the end A of a column is pinned. What are the elastic G factors for the joints A and B of the interior column?
Find the value of internal force member and state if it is in Tension or Compression
The simple beam shown, 76.2-cm. long ( = a + L + d ), is made of AISI C1022 steel, as rolled, left a forged. At a =25.4 cm , F1 = 1360.5 kg. is a dead load. At d = 25.4 in , F2 = 1088.4 kg. is repeated, reversed load. For N = 1.5 , indefinite life, and h = 3b , determine b and h . (Ignore stress concentration).
Question 22 Form the given beam loaded has shown, Ely = MAT + RĄ2² – P(x – )2 +C1 - Ely = 글MA22 + 금RAz' - 공P(z-)3 + Ciz+ Ca 3 + C1a + C2 Let P=58 kN, L = 19 m P в с D -L/3- L/2 -L/2- Determine the bending moment at point A.
Problem 7 [RC Column Design] The short spiral column shown uses eight no. 8 bars. Assume the total loading has a low eccentricity. f.' = 3500 lbf/in², and f, = 40,000 lbf/in?. Determine the design strength. 8-No. 8 bars 22 in
Determine the force in the members DF, DG, and EG of the Howe truse shown. 1000 lb 1400 lb. B C 12 E 12 G 12 12 2000 lb.